DIY Guide to Replace Apple iPhone 5c Front Camera Sensor Cable
Duration: 30 min.
Steps: 10 Steps
Welcome to your go-to guide for swapping out that troublesome front camera/sensor cable on your iPhone 5c! If your front camera is playing hide and seek, the aperture is stuck, or your photos are coming out fuzzy, it’s time for a little DIY magic. Even if your screen isn’t dimming during calls anymore, replacing this cable will bring it back to life. And don’t forget, if your microphone is ghosting you during videos or FaceTime, this fix is just what you need! Let’s get started and bring your iPhone 5c back to its shining glory. For extra help, feel free to schedule a repair!
Step 1
– Grab your pentalobe screwdriver – it’s your trusty sidekick for opening up the iPhone 5c!
– Next, let’s tackle those two pentalobe screws at the bottom of the enclosure. They’re hanging out right next to the Lightning connector, one on each side. Make sure to pop them into the same compartment of your organizer tray so they don’t go rogue! 2 x 3.8 mm pentalobe screws are waiting for you!
Step 2
– Place your iPhone 5c on a soft, clean surface to keep that back from getting scratched. We want it to look sharp!
– To get that front panel lifted, you’ll need a suction cup and a hard plastic pick. If your screen is cracked like a puzzle, just slap some packing tape over it to hold it together.
– Stick the suction cup over the Home button (if you can) or right next to it (check out figure 1). While you’re lifting the screen with the suction cup, slide that hard plastic pick between the plastic frame and the display frame, and give the plastic frame a little press down. Use the pick to help lift the screen too (see figure 2). It might take a few tries, but you got this!
– Once you can lift the screen a tiny bit (see figure 3), gently work your way around the edges until it’s loosened on both sides (see figure 4).
Step 3
– First, let’s tackle those four Phillips screws from the shiny silver cover (check out figure 1). Be sure to stash those screws in the same compartment of your organizer tray so they don’t wander off! Now, gently lift that cover off.
– Next up, it’s time to disconnect three connectors (see figure 2). Handle this part with care! Use the pointed tip of the spudger just below the contact and lift it up. You’re disconnecting the Touchscreen, LCD, and Front camera/sensor/earpiece/ambient microphone.
– Now, let’s give that new display a test run! Temporarily connect the new display assembly. Fire up your iPhone and see if the LCD and touchscreen are working their magic. Ensure all connectors are snugly plugged in; otherwise, you might end up with a black screen or some funky stripes. If the display looks a bit yellow, check out the last step in this guide.
– Don’t forget to temporarily connect that new display assembly!
– Start your iPhone and check if the LCD and touchscreen are functioning like champs. Remember to make sure those connectors are tightly plugged in; if not, you might see a black display or some stripes showing up.
– And if you notice a slight yellow tint on the display, take a peek at the final step in this guide.
Step 4
– The earpiece is nestled on the back of the display unit. Time to unscrew those two Phillips screws holding the cover in place (check out figure 1). Remember to keep them safe in the same compartment of your organizer tray! You’ve got 1 x 4.0 mm Phillips screw and 1 x 2.2 mm Phillips screw waiting for you.
– Next, let’s get that cover off! It’s got a little hook action going on in two spots. Gently detach the hooks on one side and lift out the cover. Pop it into the container with your screws from earlier (see figure 2).
– Finally, let’s unveil the earpiece (see figure 3) so you can easily remove it with your fingers. You’re doing great!
Step 5
– Let’s kick things off by gently peeling away the cable set. It’s got a bit of glue keeping it cozy with the sensors, so take your trusty laboratory spatula and coax it off carefully (check out figure 1).
– Now that you’ve freed the cable set, you can lift it up with your fingers. Just fold it over so the camera is resting above the rear panel (see figure 2). No need to worry about the heat shield; it can stay put!
– Time to remove the heat shield from the rear panel. It’s got a little adhesive love going on, so be gentle as you pull it off with your fingers. If it’s being stubborn, a little warmth from a heat gun can help soften that glue!
Step 6
Make sure to place those sensors just right! If they’re not in their happy spot, the proximity sensor might not do its thing.
– First, slide that ambient microphone into its cozy little black groove (check out figure 1).
– Next up, attach the front camera and the sensor to their designated brackets (see figure 2). It’s super important to get those sensors in just the right spot, or the proximity sensor might not be on its A-game!
Step 7
Hey there! Just a friendly reminder: those screws come in different lengths. If you mix them up, one might end up pushing against the display glass from the inside and cause some damage. So, keep them organized and safe!
– Time to put the earpiece back where it belongs (check out figure 1). Once that’s done, pop the cover back on (see figure 2).
– Now, let’s secure those Phillips screws (see figure 3). Make sure the front camera is perfectly centered on the display. If it needs a little nudge, give it a gentle push!
Step 8
Hey there, just a quick heads-up! If those connectors aren’t snug and happy, you might see some funky stripes on your display or parts of the touchscreen might decide to take a break. So, let’s make sure everything is connected just right!
– Reconnect those connectors (check out figure 1)! Just a heads up, the touchscreen connector can be a bit shy and might come loose when you’re hooking up the LCD connector. We’re talking about the Touchscreen, LCD, Front camera/sensor/earpiece/ambient microphone here!
– Once everything is snug and secure, fire up your iPhone! Test the LCD, touchscreen, proximity sensor, front camera, and earpiece. If those connectors aren’t snug as a bug, you might see some stripes on your display or parts of the touchscreen might throw a tantrum and stop working.
– Now, let’s get that cover back on and screw it in place (see figure 2). You’ll need 1 x 3.2 mm Phillips screw (not magnetic), 2 x 1.2 mm Phillips screws, and 1 x 1.7 mm Phillips screw to wrap things up!
Step 10
– Now, let’s get those two pentalobe screws at the bottom of the enclosure secured! They’re 2 x 3.8 mm pentalobe screws, just waiting to be fastened snugly in place.
0 Comment