(601) 699-8246

|

hello@salvationrepair.com

iPhone 6 – Removing the standby cable

Duration: 75 min.
Steps: 32 Steps

Welcome to your DIY adventure! In this guide, we’ll walk you through the steps to swap out that troublesome standby cable on your iPhone 6. If your standby button is feeling a bit lazy or just doesn't have that satisfying click, then it’s time for a little TLC. Don't worry, we've got your back every step of the way! Ready? Let’s dive in!

Step 1

- First things first, power down your iPhone 6 completely to keep it safe during the repair process!

- Give that standby button a gentle press for around three seconds until you see the slider pop up.

- Now, slide it to fully shut down your iPhone. This little dance might take about ten seconds, but you'll get there!

Step 2

- Ready to crack open your iPhone 6? Grab your trusty pentalobe screwdriver and let’s get started!

- Check out the lower side of your device where you'll spot two Pentalobe screws, just hanging out on either side of the Lightning connector. Carefully remove them and toss them into a designated spot on your magnetic pad to keep them safe. You're looking for two 3.8 mm pentalobe screws here!

Step 3

- Start by placing your iPhone 6 on a soft, clean surface. We want to keep that back cover scratch-free, right?

- Grab your suction cup and trusty plastic plectrum! If your screen is looking a bit like a spider web, make sure to tape it up first. Safety first—no one wants tiny glass shards flying around!

- Stick that suction cup right on the display—preferably right above the Home button, or next to it if that's tricky (check out figure 1). Use the suction cup's ring to gently lift the screen while you slide the plectrum between the aluminum and display frame, pushing the aluminum down. This will help you lift the screen with the plectrum (see figure 2). Remember, patience is key here—you might need to try a few times!

- Once you've got a little lift on the display, carefully work your way around the edges until both long sides are free (see figure 3).

Step 4

- Grab your Phillips screwdriver and get ready to unscrew those pesky Phillips screws holding the battery connector in place (check out figure 1 for a visual guide!). Once they're off, gently lift the cover (see figure 2) and make sure to toss all the parts into the same container so nothing gets lost—organization is key! You're looking at one 3.2 mm Phillips screw and one 2.3 mm Phillips screw.

- Now, let's delicately disconnect that battery connector! Use the sharp end of your ESD spudger to carefully slide underneath the plug (see figure 3). No spudger? No problem! Your fingernail can do the trick too—just be gentle!

Step 5

- Alright, let’s tackle that silver cover! It's held in place by five Phillips screws. Go ahead and remove them (check out figure 1 for a little visual help) and make sure to stash those screws in a designated spot on your magnetic pad. Once they’re out of the way, you can gently lift off the cover. You're looking at one 3.1 mm Phillips screw, three 1.3 mm Phillips screws, and one 1.8 mm Phillips screw.

- Now, take a peek at the four overlapping connectors waiting for your attention (see picture 2). Loosen them carefully, following the order below. Use the pointed side of your spudger to gently slide underneath each contact and lift it up. Here’s what you’ll be dealing with: Front camera/sensor/earpiece/ambient microphone, Touch ID cable, LCD, and Touchscreen.

Step 6

- Unscrew the two little screws securing the vibration motor (check out figure 1). You're looking for 2 x 1.5 mm Phillips screws!

- Now, with those screws out of the way, you can simply lift out the vibration motor (see figure 2). Easy peasy!

Step 7

- The battery is snug in its spot thanks to two adhesive strips. Grab your trusty spatula and gently pry the two black ends away from the battery (check out figure 1 for guidance).

- Next up, let's carefully peel off those adhesive strips. Take your time and keep them as flat as a pancake, right at iPhone height (see figures 2 and 3 for reference).

- Finally, lift that battery right out of your iPhone 6!

Step 8

- First, let's reveal that sneaky upper screw hiding in the camera cover. Check out figure 1 for a little help!

- Next, grab your Phillips screwdriver and unscrew those two Phillips screws holding the camera cover in place (see figure 2). You're looking at one 1.6 mm Phillips screw and one 2.1 mm Phillips screw.

- Now it's time to gently lift off that shiny silver camera cover (see figure 3).

- Then, using the pointed tip of your spudger, carefully slide just beneath the camera connector to disconnect it. A little lift and you're golden—see figure 4 for guidance!

- Finally, lift the camera out of your phone like a pro (see figure 5). You're doing great!

Step 9

- First up, let’s tackle those two Phillips screws holding down the silver cover (check out figure 1 for a visual!). Make sure to pop those screws into a container so they don’t go wandering off. Once they’re out, gently lift off the cover to set it free (see figure 2). You’ll be dealing with one 2.2 mm Phillips screw and one 2.9 mm Phillips screw.

Step 10

Step 11

- First remove the four Phillips screws from the Wi-Fi cover (see figure 1). Put the screws in the same container. Then lift the cover to remove it (see figure 2).2 x 2.1 mm Phillips screw1 x 1.3 mm Phillips screw1 x 1.6 mm Phillips screw

Step 12

- Time to get your screwdriver out! Unscrew those two Phillips screws from the little silver metal bracket that connects the logic board to the frame. Remember to keep all the parts together in one container—no one likes a missing screw mystery! You're looking for one 2.1 mm Phillips screw and one 1.5 mm Phillips screw.

Step 13

- Time to disconnect those connectors! Use the sharp tip of your spudger to gently pry away the Lightning connector (check out figure 1) and the antenna cable (see figure 2) from the logic board. You've got this!

Step 14

- Time to unleash that SIM card tray! You can either grab your trusty SIM Tool or a paperclip for this mission. Just gently press the SIM Tool into the tiny hole on the SIM card tray, and voilà, it pops right out!

Step 15

- Alright, time to get those five screws that keep the logic board snug in its place. Grab your Phillips screwdriver and let’s get to work (check out figure 1 for a visual!). You’ll need: 1 x 2.6 mm Phillips screw, 2 x 1.8 mm Phillips screws, 1 x 2.2 mm Phillips screw, and 1 x 1.3 mm Phillips screw.

- Heads up! The 1.3 mm Phillips screw (the green one) is holding the antenna in place (see the arrow). Make sure to remove the antenna along with that screw and keep them together with the rest of your screws.

- Once all that is done, you can gently lift the logic board out by hand (see figure 2). You’ve got this!

Step 16

- To kick things off, let’s get that Phillips screw out from the silver LED cover (check out figure 1 for a visual guide). You're looking for one 1.2 mm Phillips screw.

- Once that screw is gone, gently lift the cover to free it from its cozy spot (see figure 2).

Step 17

- First, let's get those two screws holding the standby button nice and loose (check out figure 1). You're looking for 2 x 2.2 mm Phillips screws here!

- Next, slide your trusty laboratory spatula underneath the ribbon cable and gently lift it away from the base (see figure 2).

- Now, with the spatula in hand, carefully detach the ambient microphone from the base (see figure 3).

- And just like that, you can now remove the standby cable (see figure 4). Easy peasy!

Step 18

- Alright, let’s get that standby cable back where it belongs (check out figure 1 for a visual cue) and secure it with those two trusty Phillips screws (see figure 2). You're looking for 2 x 2.2 mm Phillips screws here!

Step 19

- Now, let’s pop that silver cover back on and secure it with a screw (check out figure 1 for a little help). You're looking for one 1.2 mm Phillips screw to keep it all snug!

Step 20

- Time to place that logic board back in its cozy spot (check out figure 1) and secure it with those five Phillips screws (see figure 2). You're on the lookout for: 1 x 2.6 mm Phillips screw, 2 x 1.8 mm Phillips screws, 1 x 2.2 mm Phillips screw, and 1 x 1.3 mm Phillips screw.

- And don't forget to tuck the antenna back under the 1.3 mm Phillips screw (the green one). (Check the arrow for guidance!)

Step 21

- Alright, let's get that little silver metal bracket back in its rightful place and secure it with a couple of screws! You're on the lookout for 1 x 2.1 mm Phillips screw and 1 x 1.5 mm Phillips screw.

Step 22

- Alright, it's time to get that Wi-Fi cover back on! Just pop it into place and screw it in tight (check out figure 1). You're going to need: 2 x 2.1 mm Phillips screws, 1 x 1.3 mm Phillips screw, and 1 x 1.6 mm Phillips screw. You've got this!

Step 23

Step 24

- Now it's time to place that shiny silver cover back on (check out figure 1 for a visual). Once it's snug, grab those screws and secure it in place (see figure 2). You'll need one 2.2 mm Phillips screw and one 2.9 mm Phillips screw to keep everything tight and tidy!

Step 25

- Time to slide that camera back into its cozy spot and connect its cable (take a peek at figure 1 for guidance).

- Next up, let’s pop on the camera cover (see figure 2) and secure it with the screws (check out figure 3). You’ll need 1 x 1.6 mm Phillips screw and 1 x 2.1 mm Phillips screw.

- Finally, don’t forget to place that little black sticker back on (see figure 4) to keep everything looking sharp!

Step 26

- First, let's stick those new adhesive strips on the bottom of the battery to keep it snug and secure for the future.

- Next up, gently slide that battery into your iPhone, but hold off on connecting it just yet to avoid any potential short circuit surprises!

Step 27

- Pop that vibration motor back into its cozy spot (check out figure 1 for a visual!).

- Secure it in place with the right screws (see figure 2). You're looking for 2 x 1.5 mm Phillips screws here!

Step 28

- Alright, let's get that LCD connector attached (check out figure 1). You might need to give it a few tries, and that's totally okay! Just remember to be super gentle so you don’t bend that little plug. You’ve got this! Here’s what you’ll be connecting: Front camera/sensor/earpiece/ambient microphone, Touch ID cable, LCD, and Touchscreen.

- Once you've got those connectors snug and secure, it's time to power up your iPhone 6 again! Run a few tests to see if everything is working—LCD, touch screen, proximity sensor, front camera, and earcup. If you spot any streaks on the display or if the touchscreen is acting a bit funky, it’s a sign those connectors might need a little more love.

- Now, cover those connectors and fasten everything down with the five screws (see figure 2). You’ll need: 1 x 3.1 mm Phillips screw, 3 x 1.3 mm Phillips screws, and 1 x 1.8 mm Phillips screw.

Step 29

- Alright, let's reconnect that battery and get things buzzing again!

- Now, pop that shiny silver cover back into place and secure it with those screws—you're looking for one 3.2 mm Phillips screw and one 2.3 mm Phillips screw to keep everything snug!

Step 30

- You're almost at the finish line! Gently slide the display back into its cozy housing. Just a heads-up: avoid pinching any cables and ensure that the top edge of the screen snaps into place like a champ.

- Now, give your screen a little nudge toward the home button so it fits snugly in the frame. You're doing great!

Step 31

- Grab those last two Pentalobe screws and pop them into the lower side of your iPhone's body! You're looking for 2 x 3.8 mm pentalobe screws to finish strong!

Step 32

0 Comment

Leave a Reply

Registration isn't required.