Samsung Galaxy S7 Edge Loudspeaker Assembly Replacement
Duration: 45 minutes
Steps: 11 Steps
Get ready to tackle the loudspeaker assembly replacement in your Samsung Galaxy S7 Edge! Just a heads up, those curved edges and the super sticky adhesive can make getting started a bit tricky. Take your time, warm things up, and give it a few good pulls – the adhesive will give in eventually. You've got this!
Step 1
You can use a hair dryer, heat gun, or hot plate to help with the heat, but watch out! Too much heat can cause trouble for your phone—the OLED display and internal battery aren't fans of excessive warmth. Keep it cool and steady!
Prying open your phone will break its waterproof seals. Have some replacement adhesive on hand before you start, or be extra careful to keep liquids away if you put it back together without swapping the adhesive.
You might need to warm up and reapply the iOpener a few times to get your phone nice and toasty. Just follow the iOpener instructions so you don’t accidentally overheat anything.
- Warm up your trusty iOpener, then set it along one of the long edges of your phone for about two minutes. Give the glue a chance to loosen up—patience is your friend here.
Tools Used
Step 2
It's tricky getting that suction cup to stick on the curvy part of the glass, so don't be surprised if it gives you a little trouble!
If you find the phone's back cover is cracked, that suction cup might just slip right off. No worries, try using some strong tape, or if you're feeling crafty, superglue that cup and let it set up for a bit before giving it another go.
With that curved glass, think of it like you're pushing up instead of sliding in parallel with the phone. It's a little different, but you’ve got this!
If you're struggling a bit, don’t hesitate to heat it up more to make that adhesive nice and soft again. Just remember, it cools off quickly, so you might need to give it another round of warmth!
- Once the back panel feels nice and warm to the touch, stick a suction cup as close to the heated edge as possible—just watch out for the curved edges!
- Gently lift the suction cup and slide an opening pick under the rear glass to start the separation.
Step 3
- After getting that pick nice and snug under the glass, go ahead and warm things up again with the iOpener to melt the adhesive a bit more.
Tools Used
Step 4
Take your time, and keep the tip steady in the seam. If it gets stubborn, give it another quick warm-up with the iOpener and keep going.
- Gently slide the opening pick along the side of the phone to loosen the adhesive. Keep the pick in place and grab a second one to continue. Leaving the pick inserted helps prevent the glue from sticking back together. If you need a hand, you can always schedule a repair.
Tools Used
Step 5
- Now, let's keep the momentum going! Just like before, heat up and carefully cut around the remaining three sides of your phone. You're doing awesome!
- To keep things smooth, pop an opening pick on each side as you move on to the next. This will help stop that pesky adhesive from sticking back together. You're on the right track!
Step 6
- Gently lift the glass and peel it away from the phone. Keep it smooth and steady to avoid cracks or damage. If you need help, you can always schedule a repair.
Step 7
If you want to give your device a little extra love, feel free to reinstall the back cover without new adhesive. Just make sure to clear away any big chunks of old adhesive that might keep the back cover from sitting snugly. Once it’s in place, give it a little heat and some gentle pressure to make sure it’s secure. It may not be waterproof, but trust me, the glue usually does a great job holding it all together!
And hey, don’t forget to power up your phone and check that everything is working like a charm before you seal it all up with new adhesive!
- To put on a new back cover: If you're reusing the old cover or using one without pre-installed adhesive, follow these steps. First, use tweezers to carefully remove any leftover glue from the phone's frame. Next, clean the contact areas with high-concentration isopropyl alcohol (90% or higher) and a lint-free cloth to ensure a good bond. Then, peel the backing off the new rear glass, line up one edge with the chassis, and press it firmly into place. If you need a hand, you can always schedule a repair.
Tools Used
Step 8
- Unscrew those twelve 3.5 mm Phillips screws like a pro!
Step 9
- Find the small notch on the bottom left corner of the upper antenna and use it to gently pry the antenna out of its spot.
- Lift out the upper antenna and set it aside like a pro.
Step 10
- Gently lift out the wireless charging coil from the phone. You've got this!
Step 11
- To put your device back together, just retrace your steps in the reverse order. You've got this! If you hit a snag, remember, you can always schedule a repair for a helping hand.
