Samsung Galaxy S6 Edge Motherboard Replacement
Duration: 45 minutes
Steps: 23 Steps
Get ready to tackle your Samsung Galaxy S6 Edge by swapping out that pesky, damaged motherboard! This guide will walk you through the steps to remove the rear glass. Just a heads up, taking off the rear glass means saying goodbye to the adhesive holding it on. Don’t worry though, we’ll guide you on how to reattach it like a pro. If you need help, you can always schedule a repair.
Step 1
Hey there! Just a quick heads up: steer clear of sticking your tool into the microphone hole—it might lead to some unwanted damage. Also, keep an eye out for the SIM tray outline; it's your guide to success!
- Grab a paper clip or SIM eject tool and gently poke it into the tiny hole on the SIM card slot at the top of your phone.
- Give it a little press to pop out the SIM card tray.
- Carefully pull out the SIM card tray from your phone.
Step 2
For carousel microwaves: Double-check that the turntable spins smoothly. If your iOpener gets stuck, it might overheat and cause some unwanted burns—so keep that rotation on point.
It's a great idea to give your microwave a good scrub before diving in! Any stubborn mess on the bottom could stick to the iOpener and make things a bit tricky. So, let's keep it clean and smooth sailing ahead!
- Pop that iOpener right in the middle of the microwave and let it heat up like a champ!
Tools Used
Step 3
Hey there, just a quick heads-up! Make sure not to let that iOpener get too hot during your repair adventure. We wouldn’t want it to go boom! Keep it under 100˚C (212˚F) for a safe and smooth experience.
If the iOpener looks like it's puffed up like a balloon, steer clear of it.
Still feeling the heat? If the center of the iOpener is too toasty to handle, hang tight and let it cool down a bit more before giving it another go. A perfectly warmed iOpener should keep the good vibes for about 10 minutes.
Microwaves vary in power, so you might need to adjust the time slightly. The iOpener is ready when it's just a touch too hot to hold comfortably.
- Pop the iOpener in the microwave for thirty seconds to heat it up.
- If it starts to cool off while you’re working, just give it another quick thirty seconds in the microwave to keep things warm.
Tools Used
Step 4
The iOpener gets seriously hot—handle with care! Grab an oven mitt if you want to keep your fingers cool.
- Carefully take the iOpener out of the microwave, making sure to grab it by one of the flat ends—this way you can avoid any surprises from the hot middle!
Tools Used
Step 5
Careful now! The iOpener is going to be super toasty, so grab it by the end tabs only. Keep those fingers safe!
No microwave? No problem! Just heat up your iOpener in some boiling water with this step.
- Grab a pot or pan and fill it up with enough water to give your iOpener a nice, warm bath.
- Heat that water up until it’s boiling, then go ahead and turn off the heat. Safety first!
- Gently drop the iOpener into the hot water and let it soak for about 2-3 minutes. Make sure it's got a good splash in there!
- Using tongs (or your superhero skills), carefully fish out the warm iOpener from the water.
- Give it a good dry-off with a towel – we want it nice and cozy, not dripping wet!
- Voila! Your iOpener is all set to go! If it needs a little reheating, just repeat the process: boil the water, turn off the heat, and let it soak for 2-3 minutes again.
Tools Used
Step 6
A hair dryer, heat gun, or hot plate works for this step—just keep it cool (not literally)! Too much heat can mess up the OLED screen or the battery, so use a gentle touch.
Opening your phone? Just a heads up, that might mess with its waterproof seals. So, make sure you've got some replacement adhesive on hand before diving in, or be super careful to keep it away from any liquids if you're putting it back together without that adhesive.
Got a shattered screen? No worries! Just slap some packing tape over the whole panel to keep it nice and secure while you work on removing it.
You might find yourself needing to reheat and reapply that iOpener a few times to get your phone just the right amount of toasty. Be sure to follow the iOpener instructions so you don’t accidentally turn your phone into a sauna!
- Place the warmed-up iOpener on the back panel for about two minutes to help the adhesive let go around the edge of the glass.
- Move the iOpener to cover any spots you missed and warm those up for another two minutes.
Tools Used
Step 7
If you want to make things a little easier, slip in a few drops of isopropyl alcohol once your pick is in place—this will help loosen up the adhesive for the next steps.
- When the rear glass feels nice and warm, grab a suction cup and place it close to the bottom edge of the glass.
- Give that suction cup a gentle lift to create a little gap beneath the rear glass, then slide in an opening pick to help you on your way.
Step 8
Leave the pick hanging out in the gap while you grab a second one for the next round. This keeps the glue from sneaking back together.
Warm up the rear glass again if the glue starts acting stubborn—that sticky stuff likes to cool off and grab hold when you least expect it.
- Gently glide the pick along the bottom edge of your phone to carefully cut through the adhesive holding the rear glass in place.
Step 9
- Now, let's keep the momentum going! Just like before, heat things up and slice away at the other three sides of your phone.
- And remember, slide an opening pick under each edge to keep that pesky adhesive from sticking back together. You're doing great!
Step 10
- Grab your trusty opening pick and gently glide it through any stubborn adhesive that's holding things together.
- Carefully lift off the rear glass to reveal the inner workings of your device.
Step 11
- Let's get that new rear glass installed:
- Whether you're putting back the old rear glass or opting for one without adhesive, just follow along with this guide.
- Grab your tweezers and gently remove any leftover adhesive from the phone's chassis.
- Time to clean up! Use high concentration isopropyl alcohol (at least 90%) with a lint-free cloth. Remember to swipe in a single direction to prepare the surface for the new adhesive.
- Now, peel the backing off of the new rear glass, align one edge with the phone chassis, and press down firmly. You've got this!
Tools Used
Step 12
- Unscrew those thirteen 3.3 mm Phillips #00 screws from the midframe and get ready to dive in!
Step 13
- Gently press down on the back of the battery and carefully lift the edges of the midframe to release it from the rest of the phone. Remember to take your time and be patient, and you'll be a pro at this in no time!
Step 14
- Grab that trusty spudger and use its flat end to gently disconnect the battery ribbon cable from the motherboard. You're doing great!
Tools Used
Step 15
- Gently unplug the home button ribbon cable from the motherboard—easy does it!
Step 16
- Grab your trusty spudger and use its pointed end to carefully disconnect those two antenna interconnect cables from the motherboard. You've got this!
Tools Used
Step 17
- Gently unhook the display ribbon cable from the motherboard with the flat end of your trusty spudger. You've got this!
Tools Used
Step 18
- Gently unplug the earpiece ribbon cable from the motherboard. You've got this!
Step 19
The motherboard is sensitive to static electricity, so treat it like a diva—avoid those shocking moments! Using an anti-static bracelet is a smart move to keep things safe.
Don’t yank the motherboard out just yet—there’s a ribbon cable underneath that needs to be unplugged first. Take your time and you’ll avoid surprises!
- Get a good grip on the motherboard by holding it firmly on both edges near the top of the device.
- Now, carefully lift the motherboard up and away from the display. Be gentle, as you don't want to put too much stress on the daughterboard ribbon cable.
Step 20
- Gently unplug the daughterboard ribbon cable from the bottom of the motherboard. You've got this!
Step 21
- Grab your trusty spudger and gently lift up the connector for the front-facing camera. You've got this!
- Now, take your time and carefully detach the front-facing camera from the motherboard. Easy peasy!
Tools Used
Step 22
- Grab your trusty spudger and gently lift the connector for the rear-facing camera off the motherboard. You've got this!
- Now, carefully remove the rear-facing camera from the motherboard. Easy peasy!
Tools Used
Step 23
- Alright, you're almost there! To put your device back together, just retrace your steps in reverse. Follow this guide to snugly reinstall that rear glass.
- If you find yourself scratching your head on any tricky bits, don't hesitate to schedule a repair!