Xbox One S Motherboard Replacement Guide
Duration: 45 minutes
Steps: 15 Steps
This guide is super important because you’ll need to get to certain components on the board that might need a little TLC – aka replacing. Let’s get started and make those repairs happen!
Step 1
– Let’s get started by flipping your Xbox One S so the bottom of the case is facing up – it’s time to get a little hands-on!
Step 2
Heads up! The clips might take a little tumble when you’re taking off the bottom of the case.
As you start prying the case open, don’t be alarmed if you hear some clicking sounds! It can be a bit tricky to wiggle the bottom off.
Kick things off at the back where the warranty sticker hangs out. Gently pry along the rear edge until all the clips pop free. After that, tackle each side one at a time. Once you’ve freed up three sides, focus on the front end opposite the sync button. Take your time and be careful, and everything should come apart smoothly!
– Alright, let’s get this party started! Begin by working on the rear case where the warranty sticker hangs out. Use your trusty plastic opening tool to wedge it in between the bottom of the case and the grated top. Then you’ll spot the clips that hold the case together. Gently use your tool to pop those clips out. The best way to do this is by prying the black case away from the bottom.
– Keep on going! Use your opening tool to pop the clips out. The best way to do this is by prying the black case away from the bottom. If you need help, you can always schedule a repair
Step 3
– Now that you’ve got all the clips open, it’s time to take off the bottom part of the case.
Step 4
– Grab your trusty T10 Torx screwdriver and get ready for some action! Let’s tackle those six green 50 mm long screws from the metal case, labeled F1 through F6. Unscrew them with care and show that case who’s boss!
Step 5
– Let’s get started by carefully separating the interior case from the white exterior case – use the right technique to avoid any damage.
– Now, gently pry the white plastic sides outwards at the rear to release them from the plastic I/O shield. Take your time and be patient, it’s an easy step.
Step 6
Now you’ll be able to carefully release the plastic casing around the hard drive from the rest of the console – it’s like freeing a trapped component!
Keep in mind that some models might need a little extra attention, requiring C4 and C5 to get the job done.
– To give your Xbox One S a brand new hard drive, start by flipping it over and removing the two 10 mm T-10 Torx screws, labeled C3 and C5, from the back. This is the first step in getting your console up and running with some extra storage.
Step 7
– Carefully unplug the hard drive from the motherboard by detaching the two plastic connectors. You’ve got this!
Step 8
– To get that optical disc drive out of there, just unscrew the shiny silver 10 mm T-10 Torx screw marked ‘C4.’ Easy peasy!
Step 9
– Give that disc drive a little nudge, gently pulling it away from the motherboard. Then, disconnect the plastic connectors from the motherboard – they’re easy to spot!
Step 10
– Alright, to swap out that motherboard, let’s start by loosening up those three shiny silver 10 mm T-10 Torx screws marked ‘C1’, ‘C2’, and ‘C6’. You got this!
– Next, it’s time to tackle the four black 8 mm T-8 Torx screws labeled ‘A1’, ‘A2’, ‘A3’, and ‘A4’. Just give them a gentle twist!
Step 11
– First, track down the sleek silver clamp on the opposite side of the power block – it’s a rectangular shape, so keep an eye out for that.
– Next, gently remove the black bracket that’s hanging out near the fan. It’s time to set it free!
Step 12
Don’t worry if you need to use a bit of elbow grease to get the clamp off the silver casing – the metal is flexible and can be bent back into place without any issues. Just gently pry it off and you’ll be good to go!
Step 13
– Alright, let’s pop open this device! First things first, find those four black 8 mm T-9 Torx screws. They’re labeled “E1,” “E2,” “E3,” and “E4.” Give ’em a good turn and get ’em out of there!
Step 14
– Unscrew and say goodbye to the three black 8 mm T-9 Torx screws affectionately named ‘D1,’ ‘D2,’ and ‘D3’ to free the Mediatek board. It’s time for a little DIY magic!
Step 15
– With the clamp out of the way, it’s time to give the motherboard a gentle lift by its edges. It should slide right out of the metal casing like it’s ready for a new adventure!
