DIY Guide: Google Pixel Fold Earpiece Speaker Replacement
Duration: 45 minutes
Steps: 36 Steps
Hey there, tech enthusiasts! Don’t worry, this step-by-step repair guide was created by the awesome folks at iFixit, ensuring you’ll be in good hands. For more about our guides, peep this check it out link!
Hey there! Feel like your Pixel Fold could use a bit of help? ☆✨ We’ve got just the guide for ya! Let’s team up and swap out that earpiece speaker together. If you need help, you can always schedule a repair✨☆
Step 3
Whoa there, champ! Don’t go too deep with that pick, or you might be saying ‘bye bye’ to your screen and some of those fancy internal parts.
When you’re removing the screen, just slide your opening pick in as far as the edge goes. You’ve got this!
Step 4
If your screen is really cracked, don’t fret! Just slap on some clear packing tape to help that suction cup stick. Or, if you’re feeling bold, go for some super strong tape instead of the cup. And if you’re still struggling, a little superglue on the suction cup can do the trick with the screen.
Now, depending on how old your phone is, this might take a little extra effort. If you’re hitting a snag, just warm up the edges a bit more and give it another shot!
– Place a suction cup on the screen, aiming for the center of the bottom edge. You’ve got this!
– Gently but firmly pull up on the suction cup to create a little gap between the screen and the frame. Steady does it!
– Slide an opening pick into that gap and get ready to continue your repair adventure!
Step 5
– Gently glide that trusty opening pick along the bottom edge to break free the adhesive’s grip.
– Now, tuck the opening pick right in the bottom right corner and hold that spot before moving on.
Step 7
– Twist that opening pick around the bottom right corner to break free the adhesive. You’re doing great!
Step 8
– Slide a fresh opening pick into that bottom right corner like a pro!
– Now, gently glide the pick up towards the top right corner to break that stubborn adhesive seal.
– Keep the opening pick snugly in the top right corner while you get ready for the next step.
Step 10
– Gently twist that opening pick around the top right corner to break free the adhesive. You’ve got this!
Step 11
– Start by sliding a fresh opening pick into the top right corner of your device.
– Gently glide that pick over to the top left corner to break free the sticky adhesive holding things together.
Step 13
Hey there! Just a heads up: that sharp corner is a bit of a delicate flower. Make sure to bring out the heat and treat it with the gentleness it deserves during this step. You’ve got this!
– Position your pick so it hugs the screen as closely as possible.
– Gently twist the opening pick around the top left corner to break free the adhesive.
Step 14
– Pop in a fresh opening pick into the top left corner, like a pro!
– Gently slide that pick down toward the bottom left corner to break free the adhesive. You’ve got this!
Step 15
That corner? It’s a bit delicate! So, be sure to give it some extra love with heat and handle it with care as you navigate this step.
– Tilt your pick to keep it as flat as you can against the screen.
– Gently twist the opening pick around the bottom left corner to break the adhesive seal.
Step 18
– Alrighty, tech enthusiasts! Let’s be the screen unsung heroes. Carefully, shhh… slip an opening pick right beneath that righty edge of the screen, up near the molto top corner. And gently guide it as far as you can, without sacrificing that awesome grip you’ve got going! You got this, repair pro!
Step 19
Take it easy during this part! You’ve got this, but just be cautious—those screens can be a bit fragile. Go slowly, and if you think you need a little more heat, don’t hesitate to give it some extra love.
If you’re not feeling the adhesive loosening, add more heat or try angling the pick differently.
– Wiggle that opening pick back and forth like you’re trying to get it a dance partner! This’ll help separate the adhesive holding things together.
Step 20
Hold your horses! The screen is still hanging on by a cable, so let’s not detach it just yet.
Now that you’re here, the screen should be all set to pop off from the frame! If you feel a bit of stickiness still hanging around the edges, grab an opening pick and gently nudge it to break free any leftover adhesive.
Step 21
As you dive into this repair adventure, remember to keep an eye on each screw and return it to its original home. They get lonely, you know!
The Pixel Fold may have Torx Plus screws, but don’t sweat it—regular Torx bits will do the trick too! Just grab the same size or go one size up (like T3 or T4 bits with those 3IP Torx Plus screws), and make sure to apply steady, downward pressure to keep everything snug and strip-free!
– Let’s get this party started! Grab your trusty Torx Plus 3IP screwdriver and give those five 2.5mm screws securing the bottom bracket a good twist. Time to break free those screws!
Step 23
– Grab your trusty spudger and use the flat end to gently lift up and disconnect that flip battery press connector. You’ve got this!
– When it’s time to re-attach those press connectors, just align everything carefully and give one side a nice press until you hear that satisfying click. Then, repeat on the other side—easy peasy! Just remember, no pressing down in the middle; we don’t want any bent pins ruining our day. If you’re feeling uncertain, don’t hesitate to schedule a repair.
Tools Used
Step 24
Keep your spudger in its designated zone! Straying too far could lead to some unwanted damage to those delicate surface-mounted components on the logic board.
– Let’s disconnect the screen press connector! Take your spudger and gently slide it under the short edge of the screen press connector. You’ll want to make sure it’s facing towards the bottom of the phone.
– Now, gently pry up the connector to disconnect it. You’re doing great!
Tools Used
Step 26
Got a top right adhesive that’s still doing its sticky thing? Awesome! Feel free to give it a second life.
