Google Pixel 4 Back Panel Replacement Guide: Step-by-Step DIY
Duration: 45 minutes
Steps: 21 Steps
A heads up: this repair guide was put together by the folks at Salvation Repair, and while we’re super confident in our steps, it’s worth noting that Google hasn’t officially given it their stamp of approval. If you need help, you can always schedule a repair
Get ready to tackle that broken back glass panel on your Google Pixel 4. Our step-by-step guide, brought to you by the experts at Salvation Repair, will walk you through the process of removing or replacing it. Be aware that the wireless charging coil, LED flash, and NFC hardware are all attached to this cover, so they’ll come out as one unit. If your new part doesn’t have these components pre-installed, you’ll need to transfer them from your original panel. Removing the back glass panel is a crucial step to access all internal components. If you need help, you can always schedule a repair.
Step 1
– Grab your trusty SIM eject tool, a bit, or even a straightened paper clip, and gently slide it into the tiny hole on the SIM card tray located on the left side of your phone.
– Give it a firm press to pop that tray out like a pro.
– Now, go ahead and pull out the SIM card tray with ease.
Step 2
You can also try a hairdryer, heat gun, or hot plate, but be careful not to cook the phone—the display and internal battery are both sensitive to heat. If you need help, you can always schedule a repair
– Get ready to unlock your device’s full potential – start by applying an iOpener to the bottom edge of the back panel for about a minute. If you need help, you can always schedule a repair
Tools Used
Step 3
If your back glass is looking a bit worse for wear with some serious cracks, don’t fret! Slapping on a layer of clear packing tape might just do the trick to help that suction cup stick. If you’re feeling adventurous, you can also try using some super strong tape instead of the suction cup. And if you’re really in a bind, a little superglue on the suction cup can help it cling to the broken panel. Remember, if you need help, you can always schedule a repair.
– Now it’s time to get a grip on that back panel. Apply a suction cup to the heated edge, pressing down firmly to create suction – try to get it as close to the edge as possible. If you need help, you can always schedule a repair
Step 4
Hey there! This might be a bit tricky, especially if the phone is getting on in years. If you’re feeling discouraged, give that edge some more heat and give it another go. And remember, if you need a hand, the folks at Salvation Repair are always happy to help!
– Alright, time to get that back panel unstuck! Grab your suction cup and give it a good, strong pull. You want to create a little gap between the panel and the frame – think of it as a mini escape route for your phone.
– Now, slip the tip of your opening pick into that gap you just made. It’s like giving your phone a little nudge to say, ‘Hey, time to come apart!’
Step 5
– Let’s get this party started! Slide your opening pick across the bottom towards the left corner and gently slice through the adhesive. You’re like a ninja!
– Keep your pick in the game and slide it from the bottom left corner over to the bottom right corner. We’re almost there!
– Hold your pick in the bottom right corner to prevent the adhesive from sealing itself back up. You’re a pro! If you need help, you can always schedule a repair
Step 6
– Grab your trusty iOpener and give it a warm hug on the left edge of your phone for a whole minute. It’s like a cozy spa day for your device!
Tools Used
Step 7
– Let’s get that back panel popping! Take your trusty opening pick and slide it under the back panel, right over the charge port.
– Now, glide that pick smoothly to the bottom left corner of the phone. We’re almost there!
Step 8
That sticky stuff can be a real pain! Just keep wiggling that pick back and forth, like you’re sawing through a giant, gummy bear. You got this!
– Gently glide the opening pick around the bottom left corner and along the left side of the phone to cut through that sticky adhesive.
– Pause when you hit the top left corner, close to the camera, and keep the pick in place.
Step 9
– Get your iOpener ready and give the right edge of the phone a warm hug for about a minute. Let the heat work its magic!
Tools Used
Step 10
– Alright, now let’s keep those opening picks in place and add another one to the lower part of the right side. We’re going to slide this new pick up towards the top of the phone, carefully separating the adhesive on the right side. When you reach the top right corner, stop and keep that pick in place. You got this!
Step 11
– Hey there! This might seem a little tricky, but you’ve got this. Now, let’s slice up that last bit of adhesive by sliding the third opening pick around the top right corner and across the top side of your device. You’re doing great! If you need help, you can always schedule a repair with us!
Step 12
– Now, picture this: you’re a magician about to reveal the phone’s inner secrets! Go ahead and slice around the edge with your trusty tool, but don’t get too excited just yet. Give the back cover a gentle lift on the right side – think of it like opening a book. Hold your horses though, the cover is still attached to the phone, so don’t try to pull it all the way off just yet. We’ll get there!
Step 13
– Keep swinging that back panel open until it’s nice and comfy resting on the left side of your phone. Just be gentle, don’t want to put any strain on that ribbon cable, right?
– Hey, now’s a good time to turn your phone on and make sure everything’s working like a charm before you seal things up. Don’t forget to shut it down completely once you’re done testing! If you need help with any of this, you can always schedule a repair.
Step 14
As you dive into this repair adventure, be sure to keep an eye on every screw. They all have their special place, and we want them to return home just right!
– First things first, let’s pop off the battery connector shield by removing those five T3 Torx screws. Here’s the scoop: you’ll need four 4.0 mm screws and one sneaky little 2.1 mm screw. Let’s get to it!
Step 15
– Time to get up close and personal with those tiny parts! Use a trusty pair of tweezers to carefully remove the battery connector shield. If you need help, you can always schedule a repair
Tools Used
Step 16
Be careful when using the spudger near the battery – we don’t want any accidental punctures! If you’re not comfortable with this step, don’t worry, you can always schedule a repair
– Alright, let’s disconnect that battery! Use the pointed end of your spudger to gently pry the battery connector straight up from the motherboard. It’s like giving it a little high five, but with a tool. 😉
– Now, to reconnect, make sure you line up the connector perfectly. Press down on one side until it clicks, then repeat on the other. Don’t press in the middle, it’s not a trampoline! If the connector’s not lined up, those little pins can get bent and that’s not cool. If you’re feeling a bit unsure, you can always schedule a repair.
Tools Used
Step 18
– Use a T3 Torx driver to remove the two 4 mm screws holding the back panel connector cover in place. Let’s get those screws out and keep on moving! If you need help, you can always schedule a repair
Step 20
– Time to get started! Use the pointed end of a spudger to carefully pry up and disconnect the back panel connector. If you need help, you can always schedule a repair
Tools Used
Step 21
– Take off the back panel – it’s the first step to getting your device fixed up.
– When you’re putting everything back together, be sure to check out our guide on how to install custom-cut adhesives for your device.
– If you’re using a pre-cut adhesive card, follow along with this guide for a smooth repair process. And remember, if you need help, you can always schedule a repair
