Samsung Galaxy S24+ Earpiece Speaker Replacement Guide – DIY Repair Tutorial

– Alright, let’s power down your phone. Unplug any cables. Then, hold the side key and the volume down button. Next, tap “Power off” to shut things down. You got this!

– Warm up an iOpener and place it on the right edge of the back cover for a chill two minutes.

– Grab your trusty suction handle and stick it to the back cover, aiming for the center of the right edge.

– Now, give that suction handle a good pull, like you’re trying to open a stubborn jar, to create a tiny gap between the cover and the frame.

– Slide in your opening pick into that gap, like you’re slipping into your favorite comfy shoes.

– Slide the pick back and forth along the right edge to loosen the adhesive.

– Leave the pick inserted near the bottom right corner to keep the adhesive from sticking back together.

– Let’s warm up that back cover! Apply a heated iOpener to the bottom edge for about two minutes. You got this!

– Now, let’s get that adhesive loosened up! Rotate the opening pick around the bottom right corner. You’ve got this! We believe in you! If you need help, you can always schedule a repair

– Let’s get this party started! Insert a second pick at the bottom right corner.

– Now, slide the opening pick to the bottom left corner to separate the adhesive. You got this!

– Leave the pick in the bottom left corner to prevent the adhesive from resealing. You’re doing great!

– Let’s get this party started! Apply a heated iOpener to the left edge of the back cover for two minutes. If you’re struggling, you can always schedule a repair

– Gently spin that opening pick around the bottom left corner to break free the adhesive like a pro!

– Alright, time to get funky with this phone! Let’s slide a third opening pick in at the bottom left corner.

– Now, slide that pick towards the top left corner, like you’re giving the adhesive a little high five. We’re gonna gently separate those two lovebirds.

– Leave the pick hanging out near the top left corner, keeping that adhesive from getting cozy again. We’ve got work to do!

– Let’s warm up that back cover! Use a heated iOpener to gently apply heat to the top edge of the back cover for about two minutes. Think of it like a nice warm hug for your device.

– Give that opening pick a little spin around the top left corner to break free the adhesive. You’re doing great!

– Pop in a fourth opening pick at the top left corner—you’re doing great!

– Gently slide that pick over to the top right corner to break free the adhesive. Keep that momentum going!

– Once you’re in the groove, leave the pick hanging out near the top right corner so the adhesive doesn’t decide to play hide and seek again.

– Get your opening pick ready and line it up with the flash – this is where the magic starts.

– Gently slide the pick under the top of the back cover until you feel it catch on the adhesive. Don’t worry, it’s supposed to do that.

– Keep sliding the pick down toward the bottom of the phone, and as you do, carefully lift the cover until it’s free from the adhesive. If you need help, you can always schedule a repair

– First things first, let’s get that back cover off! Grab it and give it a gentle pull.

– Now, as you put everything back together:

– If you’re having a tough time with the sticky stuff, don’t sweat it! Use some tweezers or your fingers to peel off all the adhesive from both the back cover and the phone. A little heat or some isopropyl alcohol (90% or greater) along with a coffee filter or lint-free cloth can work wonders if the adhesive is being stubborn.

– And if you’re using custom-cut adhesives, just follow this guide.

– Grab your trusty spudger and gently pry up to disconnect the wireless charging coil press connector from the motherboard. Easy peasy!

– To get those press connectors back together, just line them up with their socket and give a gentle push with your fingertip—first one side, then the other—until you hear that satisfying click. Remember, no need to force it! If it’s being tricky, reposition and give it another go.

– Grab your trusty Phillips screwdriver and get ready to loosen those thirteen little 3.5mm screws holding down the wireless charging coil and the loudspeaker. That’s six screws for the wireless charging coil and seven for the loudspeaker. You got this!

– Slide the spudger’s point into the notch at the top left corner of the loudspeaker, where you’ll spot a handy little arrow guiding your way.

– Gently pry upwards to release the loudspeaker from its snug spot in the frame.

– Give that loudspeaker a little love tap with your fingers and gently lift it away from the frame. It’s like a mini-dance party for your phone!

– Time to remove the wireless charging coil and loudspeaker from the frame. Think of it like giving them a vacation from their hard work!

– Now, when you put everything back together, gently press around the edges of the loudspeaker to make sure it’s snug in its frame before you screw things back in. It’s all about a good fit!

– Time to get started! Use a spudger to carefully pry up and disconnect the battery press connector. If you need help, you can always schedule a repair

– Grab your trusty spudger and gently pry up to disconnect the earpiece speaker press connector. You’ve got this!

– Let’s get started by removing the five 3.5mm-long screws that hold the earpiece speaker in place – just grab a Phillips screwdriver and you’re all set. If you need help, you can always schedule a repair

– Hey, you got this! Let’s tap that spudger like a boss and pry open that earpiece speaker compartment – watch out, metal plate, here comes the flat end!

– Now twist that spudger like you’re dancing to your favorite jam, and unclip that earpiece speaker – it’s getting a well-deserved vacay!

– Last but not least, let’s snap that earpiece speaker back into place like you’re reuniting long-lost friends. Oh, and remember, if you get stuck, you can always schedule a repair and give us a holler!