DIY Guide: Replace Samsung Galaxy Note USB Board Step-by-Step

– Grab the stylus cap and gently pull it out from its cozy spot in the midframe.

– Let’s get this party started! Gently pry with a plastic opening tool, or your fingernail, in the little notch to the right of the rear-facing camera, near the volume rocker. If you need help, you can always schedule a repair

– Let’s get started by carefully lifting and removing the rear case from your phone. This is the first step in giving your device a brand new lease on life. If you need help, you can always schedule a repair

– Slide your finger into the little groove of the battery compartment.

– Gently nudge the battery towards the rear-facing camera while pulling it out.

– Use the flat end of a spudger, or your fingernail, to give that microSD card a little nudge deeper into its slot. You’ll hear a click when it’s in the right spot.

– After the click, let go of the card and watch it pop out! Easy peasy, right?

– To put it back together, just slide the microSD card into the slot until it clicks. And that’s it! If you need help, you can always schedule a repair

– Let’s get started by carefully removing the microSD card from its slot in the midframe. If you need help, you can always schedule a repair

– Get ready to rock and roll with your phone’s SIM card removal! Gently slide in that trusty plastic opening tool or your nail, and give it a little push to pop that card right out. Then, you’ll be on your way to connecting with the world like a boss!

– Now it’s time to set that SIM card free – gently slide it out the rest of the way with your thumb and remove it from the device. If you need help, you can always schedule a repair

– Let’s get started by removing the nine 3.4 mm Phillips #00 screws that hold the midframe in place on the display assembly. If you need help, you can always schedule a repair

– Gently slide your trusty plastic opening tool to the left of the power button, slipping it between the midframe and the front panel assembly. Give it a little pry and watch the magic happen!

– Let’s get that plastic opening tool sliding down the seam. It’s like giving your device a little hug, but with a tool instead!

– Alright, let’s get this party started! We’re gonna slide our plastic opening tool in between the midframe and the display assembly, right next to the headphone jack. Think of it like a little dance move.

– Now, scoot that tool along the top of the phone. It’s like we’re giving the phone a little high five.

– Keep sliding that tool all the way around the phone, separating the midframe. You’re doing great!

– Need a helping hand? You can always schedule a repair with Salvation Repair.

– Alright, let’s get that midframe separated from the display assembly. It’s like a little dance, just a gentle separation, you know? If you need help with this step, you can always schedule a repair.

– Whoa, buddy… Careful over there with the display cable connector! Use the flat end of a spudger like a pro, and gently disconnect it, you got this! If you need help, you can always schedule a repair.

– Let’s unplug the front-facing camera assembly cable connector with our trusty spudger.

– Next, we’ll disconnect the headphone jack/earpiece speaker assembly cable connector.

– Finally, we’ll disconnect the digitizer cable connector.

– Gently pry off the soft button cable connector using the flat end of your trusty spudger.

– Next up, use that same spudger to disconnect the USB board cable connector like a pro.

– Now, let’s disconnect the antenna cable connector and keep this repair rolling!

– Have a blast unscrewing the two 3.4 mm Phillips #00 screws holding the motherboard to the display assembly. Your device is on its way to being fixed!

– Let’s get started by carefully removing the motherboard assembly from the display assembly. Take your time and make sure everything is properly disconnected before lifting it out.

– Let’s get started by removing the three 3 mm Phillips #00 screws that hold the speaker enclosure in place on the front panel assembly. If you need help, you can always schedule a repair

– Time to get this repair started – gently lift the speaker enclosure away from the display assembly.

– Grab your trusty spudger and gently pry off the antenna cable connector from the USB board. You’ve got this!

– Now, carefully remove the antenna cable. You’re one step closer to getting your device back in action!

– Slide the flat edge of a spudger beneath the USB board to gently lift it away from the display assembly. Take your time, and remember—every little action counts on this repair journey!

– Alright, let’s get that USB board outta there!