DIY Samsung Galaxy S6 Edge Rear Glass Replacement Guide
Duration: 45 minutes
Steps: 10 Steps
We tackled this guide on a Samsung Galaxy S6 (non-Edge), but don’t worry, the steps are exactly the same for you! Just make sure to grab some S6 Edge adhesive that matches the stuff you peeled off the rear glass, as it might be different from what you see here. You’ve got this!
Get ready to tackle that pesky damaged rear glass panel on your Samsung Galaxy S6 Edge! Whether you’re replacing it or just popping it off to explore the magic inside, this guide has got your back. Keep in mind, though, that removing the rear glass will mean saying goodbye to that adhesive keeping it snug. But don’t worry, we’ll walk you through how to put it all back together. This guide is based on a Samsung Galaxy S6 (non-Edge), but you’ll find the steps are a perfect match for your S6 Edge. Just make sure to grab some S6 Edge adhesive that matches what you’ve removed, as it might be different from the one in this guide. If you need help, you can always schedule a repair.
Step 1
For carousel microwaves: Ensure the plate has the freedom to spin like a dancer! If your iOpener gets a bit too cozy and gets stuck, it might just overheat and cause some unwanted drama.
Before you dive into the repair, why not show your iOpener some love with a quick cleanup? A sparkling iOpener makes for a smooth fix, no gunk included! If you need assistance, you can always schedule a repair.
– Pop the iOpener right in the middle of the microwave and let it warm up a bit.
Tools Used
Step 2
Hey there! When using the iOpener during the repair, just remember not to get it too hot. Heating it too much could lead to it bursting, and we definitely don’t want that! Keep it under 100˚C (212˚F).
If you notice the iOpener looking a bit swollen, best to keep your hands off it!
If the middle of the iOpener still feels too hot to handle, no worries! Just keep using it gently until it cools down a bit more. A well-heated iOpener stays warm for a good 10 minutes. Keep that heat going!
Depending on your microwave’s power level, you might need to adjust the time a bit. The iOpener is ready to roll when it feels just a tad too hot to handle.
– Zap the iOpener in the microwave for thirty seconds.
– As the iOpener cools down during the repair, pop it back in the microwave for another thirty-second blast as needed.
Tools Used
Step 3
Watch out—the iOpener will be super hot! Handle with care and use an oven mitt if needed.
– Alrighty, time to defrost that io(i)pen! Carefully grab it by one of those flat ends – remember, the middle gets hot AF, so be cautious! If you’re feeling a bit stuck or messy, we’ve got your back! If you need help, you can always schedule a repair!
Tools Used
Step 4
Remember, the iOpener gets pretty toasty, so make sure to hold it delicately by the end tabs.
No microwave? No problem! Just pop your iOpener into some boiling water to warm it up.
– Grab a pot or pan and fill it up with enough water to completely dunk an iOpener.
– Get that water boiling hot, then turn off the heat.
– Drop the iOpener into the steamy water and let it chill out for 2-3 minutes. Just make sure it’s all the way in there.
– Bust out your tongs and rescue the toasty iOpener from its spa day.
– Give that iOpener a good towel dry-down.
– Your iOpener is good to go! If you ever need to warm it up again, just bring the water to a boil, turn off the heat, and toss the iOpener back in for 2-3 minutes.
Tools Used
Step 5
You can use a hair dryer, heat gun, or hot plate, but remember to keep it cool! Overheating your phone can lead to some serious heat damage for the OLED display and internal battery. Stay chill while you repair!
Opening up your phone? Just a heads up, you’ll be breaking those waterproof seals. Make sure you’ve got some replacement adhesive handy before you dive in, or be super careful to keep it away from any liquids if you’re reassembling without the new adhesive.
Got a shattered glass? No worries! Just slap some packing tape over the whole panel to keep it intact while you work your magic removing it.
You might find yourself reheating and applying the iOpener a few times to get that phone nice and toasty. Just follow the iOpener instructions so you don’t accidentally turn it into a mini sauna!
– Place the warm iOpener on the back panel for about two minutes to help loosen up that sticky adhesive around the glass edges.
– Move the iOpener to heat up the rest of the panel for another two minutes.
Tools Used
Step 6
If you’re feeling brave, slide in that pick and drizzle a few drops of isopropyl alcohol into the gap. This will make your next moves easier by loosening up that sticky adhesive.
– Once the rear glass is feeling warm and cozy, pop a suction cup near the bottom edge of that glass.
– Give the suction cup a gentle tug to open up a tiny gap beneath the rear glass, and then slide an opening pick into that sweet little space.
Step 7
To keep things smooth sailing, consider leaving the pick in place while you grab a second one for the next step. This little trick can help stop that pesky glue from sticking back together.
Don’t forget to give the rear glass a little heat boost as needed to keep the glue from cooling off and getting all hard on you.
– Gently glide the pick along the bottom edge of your phone to break through the adhesive that’s holding the rear glass in place.
Step 8
– Keep the good times rolling by warming up and slicing through the remaining three sides of your phone.
– Once you’ve made some progress, slide an opening pick under each edge to keep the adhesive from getting a little too cozy and sealing up again.
Step 9
– Grab your trusty opening pick and gently slide it through any stubborn adhesive left hanging around. It’s like giving your device a little spa treatment!
– Now, with a bit of finesse, lift off the rear glass. You’re doing great!
Step 10
– Ready to jazz up the back of your device?
– If you’re putting back the old rear glass or using glass without sticky stuff on it, check out this guide for some cool moves!
– Grab tweezers and gently strip off any leftover goo from your device’s frame.
– Spruce up the sticky spots with super strong isopropyl alcohol (90% or more) and a lint-free cloth. Swipe in just one direction – smooth moves make the surface happy for the new sticky stuff.
– Peel the backing off the new glass, slide one side up to your device’s frame, and firmly press that glass on like a boss.
Tools Used
