DIY Samsung Galaxy A15 Battery Replacement Guide
Duration: 45 minutes
Steps: 30 Steps
Ready to give your Samsung Galaxy A15 a little love? This guide will walk you through replacing that battery like a pro! When you’re putting your device back together, don’t forget to grab some replacement adhesive for the back cover along with your shiny new battery. If your new battery is lacking adhesive, no worries—stretch release adhesive to the rescue! And remember, if your battery looks a bit swollen, play it safe and take the right precautions. If you need help, you can always schedule a repair.
Step 1
– First things first, let’s give your phone a little break! Unplug all those cables and power it down completely.
– Now, it’s time to channel your inner tech wizard! Press and hold the power button along with the volume down button at the same time to summon the shutdown menu.
Step 2
A hair dryer can be handy for this task, but watch out! You don’t want to turn your phone into a hot potato. The display, internal battery, and plastic back can easily get damaged by too much heat. Aim for a temperature that feels just warm enough to bring a smile, not a burn!
– Warm up that iOpener and gently press it against the right edge of the back cover for a solid two minutes. You’ve got this!
Tools Used
Step 3
Heads up! There’s an extra layer of adhesive chilling at the bottom of the phone. Other than that spot, keep your digging no deeper than 4 mm from the edge. If you need help, you can always schedule a repair.
– While the adhesive is taking its sweet time to soften, here’s a little nugget of wisdom for you:
– There’s some sticky stuff holding the back cover in place all around the edge of the frame.
Step 4
If you’re having a bit of a struggle, just crank up the heat a notch to help loosen that adhesive even more.
– Grab that suction handle and stick it on the back cover, aiming for a spot near the center of the right edge.
– Give the suction handle a good, steady pull to create a little gap between the cover and the frame.
– Slide an opening pick into that gap you’ve just made.
Tools Used
Step 5
– Gently slide your opening pick along the right edge, wedging it between the back cover and the frame to gracefully cut through that pesky adhesive.
– Nestle your opening pick in the bottom right corner to prevent the adhesive from re-sticking. You’ve got this!
Step 6
– Warm up your iOpener and place it on the bottom of the back cover for a cozy two minutes.
Tools Used
Step 7
– Grab another opening pick and slide it into the bottom right corner. Give it a gentle nudge along the bottom edge to cut through that sticky adhesive like a pro.
– Keep your opening pick snug in the bottom left corner to ensure that pesky adhesive doesn’t seal itself back up on you.
Step 8
– Give your iOpener a little warm-up, then place it on the left side of the back cover for a cozy two minutes.
Tools Used
Step 9
Hey there! Just a friendly reminder to only slide your pick in to about 4 mm deep. We want to keep those rear cameras and flash safe and sound!
– Slide another opening pick into the bottom left corner and glide it along the left edge to cut through that sticky adhesive like a pro.
– Keep your opening pick in the top left corner to stop the adhesive from sealing back up. You’re doing great!
Step 10
– Warm up your trusty iOpener and give it a cozy two-minute hug on the top of the back cover. It’s a little heat therapy that goes a long way!
Tools Used
Step 11
– Pop in another opening pick at the top left corner, keeping it at the same depth, and gently slide it along the top edge to cut through the adhesive like a pro.
– Keep your opening pick snugly in the top right corner to stop that adhesive from making a comeback!
Step 12
Hey friend, just slide your pick in up to 4 mm to keep those rear cameras and flash safe. If you need help, you can always schedule a repair
– Gently slide your opening pick along the top edge of the phone and give it a little twist to release those camera clips.
– Now, take that same pick and glide it around the edges of the camera modules to free up the rest of those clips.
Step 13
– Once the sticky stuff around the edges is feeling loose, gently slide your opening pick in deeper along the bottom edge, starting from the bottom left corner.
– Now, keep that pick moving deeper into the phone along the bottom edge, cutting through the rest of the adhesive like a pro!
Step 14
Now’s the perfect moment to power up your phone and give all the functions a quick test before sealing it up tight. Just remember to turn your phone off completely before diving back into the repair work!
– Time to lift off that back cover like a pro!
– On to the reassembly phase:
– Use tweezers or your fingers to eliminate any pesky adhesive bits. If it’s giving you a tough time, a little heat and some 90% or greater isopropyl alcohol can work wonders.
– Got custom-cut adhesives? Check out this guide.
– Using double-sided tape? This guide has got you covered.
Tools Used
Step 15
– Grab your SIM card eject tool, a bit, or even a straightened paperclip. Locate the hole on the SIM tray towards the top-left edge of your phone, and pop that tool in there!
– Push firmly to eject the tray and remove it. If you need help, you can always schedule a repair
Tools Used
Step 16
– Time to get those fifteen 4 mm-long screws out! They’re holding the frame to the chassis like a tight hug. Grab your screwdriver and let’s break free!
Step 17
– Grab your spudger and use the flat end to gently pry up and disconnect that fingerprint button press connector from the motherboard. You’re doing great!
Tools Used
Step 18
– Gently slide your opening pick right above the SIM card tray cutout to create a little gap between the frame and your phone. No pressure, just a nice little nudge!
– Now, take that same pick and glide it down the left edge of your device to release those frame clips. You’re doing great!
Step 19
If your opening pick decides to take a little vacation from the phone, just pop it back in at the last corner that was feeling a bit loose.
– Keep sliding your opening pick around the edges of the phone until you’ve popped off all the clips. If you need help, you can always schedule a repair
Step 21
– Grab your trusty spudger and gently lift up to disconnect the battery press connector from the motherboard. You’ve got this!
Tools Used
Step 22
Hey there! Just a quick heads up: the connector marked ‘OCTA’ isn’t plugged into the board; it’s actually connected to the display cable. So, go ahead and gently disconnect those connectors from each other. You’ve got this!
– Slide the flat end of a spudger under the edge of the top ‘OCTA’ cable connector.
– Carefully pry up the top connector away from the bottom one until they’re disconnected.
Tools Used
Step 24
– Gently use the flat end of a spudger to pop up the ‘MAIN’ connector from the motherboard and disconnect it. If you need help, you can always schedule a repair
Tools Used
Step 25
– Grab that interconnect cable and gently detach it from the phone.
Step 26
– Gently lift that cheerful blue battery pull tab until it’s all yours to grab with your fingers!
Step 27
Make sure those tabs are fully separated, or you might find it tricky to lift the battery in the next step!
– Gently use your fingers to pop off the two small tabs from the top and bottom corners of the battery’s left edge. If you need help, you can always schedule a repair
Step 28
Be gentle with that battery! Bending or creasing it could lead to leaks of harmful chemicals or even a little fire action—yikes!
If the battery is feeling stubborn, try putting a few drops of isopropyl alcohol (90% or greater) underneath it, give it a few minutes to work its magic, and then give it another go!
– Using one hand, gently push the upper and lower tabs away from the battery while keeping the frame steady. You’ve got this!
– With a confident pull on the blue battery tab, lift with a firm, steady motion until the battery releases from its adhesive snugly holding it in place. Easy peasy!
Tools Used
Step 29
– Gently peel off the rest of the battery adhesive from your phone’s frame. If you need help, you can always schedule a repair.