Galaxy Note10 Plus Loudspeaker Replacement Guide: DIY Tutorial for a Crisp Sound Experience

Duration: 45 minutes
Steps: 12 Steps

Get ready to breathe new life into your Samsung Galaxy Note10+ by replacing or removing the loudspeaker. Fun fact: the daughterboard cover also serves as the main downwards-facing loudspeaker. If you need help, you can always schedule a repair

Step 1

– Get ready to unlock your device’s full potential – start by applying an iOpener to the left edge of the rear cover for about a minute. If you need help, you can always schedule a repair

Tools Used
  1. iOpenerGalaxy Note10 Plus Loudspeaker Replacement

Step 2

– Grab a suction cup and stick it to the warm edge of the rear cover, getting as close to the edge as you can.

– Give that suction cup a good, steady pull to open up a little gap between the rear cover and the frame.

– Slide the tip of an opening pick into that gap you’ve just created.

Step 3

– Now it’s time to get this repair started – slide the opening pick along the left edge towards the bottom left corner. This will help you slice through the adhesive and make the rest of the process a whole lot easier.

– Great job so far! Leave the pick inserted in the bottom left corner to prevent the adhesive from re-sealing. If you need help or get stuck, you can always schedule a repair

Step 4

– Go ahead and give the other three sides of your phone some love with the same heating and cutting dance you just did! You’re on a roll!

– To keep the adhesive from playing tricks on you, leave an opening pick on each side before moving on to the next. You’ve got this!

Step 5

– Time to get started! Lift that rear cover straight up and off you go – it’s the first step to getting your device back in action.

– Ready to put everything back together? Follow our guide to reinstall the rear cover and get the adhesive just right.

– Using Tesa tape to reattach some components? No problem! We’ve got a guide for that too – just follow along and you’ll be all set. And if you need help, you can always schedule a repair.

Step 6

– Alright, let’s get this show on the road! Grab your trusty Phillips screwdriver and give those five 4mm screws securing the wireless charging coil a little spin to the left. You got this!

Step 7

– Grab a trusty pair of tweezers and gently lift up that metal shield hiding the battery connector. Don’t be shy, give it a little flip back to reveal the magic inside!

Tools Used
  1. TweezersGalaxy Note10 Plus Loudspeaker Replacement

Step 8

– While keeping the metal shield safely out of your way, grab your trusty spudger and use its pointed end to gently lift the battery connector and disconnect it.

Tools Used
  1. SpudgerGalaxy Note10 Plus Loudspeaker Replacement

Step 9

– Grab that trusty spudger and use its sharp tip to gently detach the wireless charging coil connector from the motherboard. You’ve got this!

Tools Used
  1. SpudgerGalaxy Note10 Plus Loudspeaker Replacement

Step 10

– Time to get a grip – carefully tilt the metal shielding up so you can get a good hold of it with your fingers.

– Now, let’s get that wireless charging coil out of the way – simply peel it up and away from the device.

– The final step: remove the wireless charging coil. If you need help, you can always schedule a repair

Step 11

– Time to get those screws out! Use a Phillips screwdriver to loosen up those five 4 mm screws holding the loudspeaker in place.

Step 12

– Time to get up close and personal with those tiny components – use a trusty pair of tweezers to carefully remove the loudspeaker. If you need help, you can always schedule a repair

Tools Used
  1. TweezersGalaxy Note10 Plus Loudspeaker Replacement

Leave a Reply

Your email address will not be published. Required fields are marked *

🍪
Have a cookie! This site uses cookies to enhance your experience. Opt-Out Options.