How to Replace iPad 3G Dock Connector Cable Tutorial
Duration: 45 minutes
Steps: 17 Steps
Heads up! Before you dive into this repair, make sure you’ve got everything you need. If you ever feel stuck or need a hand, don’t hesitate to schedule a repair. We’re here to help you get back on track!
Get ready to tackle that iPad connector cable replacement like a pro! This guide will walk you through each step of the process, making it easier than you think. If you need help, you can always schedule a repair.
Step 1
Put on those safety glasses to keep your peepers safe, and remember to treat that LCD screen like the delicate gem it is!
– Got a cracked display? No worries! Keep any further shattering in check and avoid any accidents during your repair by sticking some tape on that glass.
– Grab some clear packing tape and lay it down in overlapping strips over the iPad’s display until it’s completely covered. You’ve got this!
– Try your best to stick to the guide from here on out. Just a heads up: once that glass breaks, it might keep cracking while you work. Don’t be surprised if you need to use a metal prying tool to gently scoop the glass out.
Step 2
The iPad in the pictures might have a slightly different look than yours, but no worries—the steps are exactly the same!
– Gently slide a metal spudger between the right edge of the display assembly and the rear panel assembly. You’re doing great!
– Now, give that spudger a little twist away from you to pop those tabs loose along the top edge of the display. Keep it up!
Tools Used
Step 3
– Slide a second metal spudger into the gap between the top edge of the display assembly and the rear panel assembly. This will keep those pesky tabs from snapping back into place.
– Gently pry the display assembly away from the rear panel. You’re doing great!
Tools Used
Step 4
Be super careful as you get close to the top edge of the iPad! The digitizer ribbon cable is hanging out near the rear panel edge, and it’s a bit fragile—easy to mess up if you’re not watching out.
– Keep gently prying the display assembly away from the rear panel along the bottom and left edges of the iPad. You’re doing great, just take your time!
Step 6
– Gently slide the flat end of a spudger under the antenna connector located nearest to the bottom of your iPad and carefully lift it away from its socket on the communications board. You’ve got this!
Step 7
– Alright, let’s get down to business! In the upcoming steps, we’re going to gently unhook the three cables that connect your display assembly to the logic board. These cables are responsible for some important components, so let’s treat them with care!
Step 8
Just a friendly reminder: make sure you’re lifting the retaining flap, not the socket itself!
– Grab that trusty iPod opening tool and gently nudge up those little retaining flaps that are keeping the digitizer ribbon cables snug in their cozy sockets on the logic board.
– Now, with a steady hand, pull those digitizer ribbon cables straight out of their sockets like you’re pulling off a band-aid. Easy peasy!
Step 9
– Grab your trusty iPod opening tool and gently nudge the ambient light sensor connector upward to free it from its cozy socket. You’ve got this!
Step 10
Gently slide the connector away from the logic board, keeping it parallel to the surface. You’re doing great!
– Gently lift the metal retainer using the black plastic pull tab to free the display data cable from the main board. Easy peasy!
– Now, give that cable connector a little tug and pull it away from its socket. You’ve got this!
Step 11
– Gently detach the display assembly from the rear panel assembly. You’ve got this!
Step 12
– Let’s get started! First, grab your trusty T5 Torx screwdriver and carefully remove the two 4.56 mm screws that are holding the dock connector cable to the main board. You’re doing great!
Step 13
– Unscrew the lone 2.84 mm T5 Torx screw that’s holding the dock connector cable snugly to the rear case assembly. You’ve got this!
Step 14
– Unscrew those two 2.84 mm T5 Torx screws holding the dock connector cable in place on the rear panel assembly. You’ve got this!
Step 15
– Gently take off the plastic cover that’s hanging out over the WiFi/Bluetooth board and dock connector cable. A trusty iPod opening tool will be your best buddy for this task!
Step 16
– H
– e
– y
–
– t
– h
– e
– r
– e
– !
–
– W
– a
– n
– t
–
– t
– o
–
– g
– i
– v
– e
–
– t
– h
– o
– s
– e
–
– W
– i
– –
– F
– i
–
– a
– n
– d
–
– B
– l
– u
– e
– t
– o
– o
– t
– h
–
– a
– n
– t
– e
– n
– n
– a
– s
–
– a
–
– l
– i
– t
– t
– l
– e
–
– n
– u
– d
– g
– e
–
– b
– a
– c
– k
–
– t
– o
–
– t
– h
– e
– i
– r
–
– h
– o
– m
– e
–
– s
– w
– e
– e
– t
–
– h
– o
– m
– e
–
– o
– n
–
– t
– h
– e
–
– W
– i
– –
– F
– i
– /
– B
– l
– u
– e
– t
– o
– o
– t
– h
–
– b
– o
– a
– r
– d
– ?
–
– D
– o
– n
– ‘
– t
–
– b
– e
–
– a
–
– s
– t
– r
– a
– n
– g
– e
– r
– ,
–
– y
– o
– u
– ‘
– v
– e
–
– g
– o
– t
–
– t
– h
– i
– s
– !
–
– I
– f
–
– y
– o
– u
–
– n
– e
– e
– d
–
– h
– e
– l
– p
– ,
–
– y
– o
– u
–
– c
– a
– n
–
– a
– l
– w
– a
– y
– s
–
– <
– a
–
– h
– r
– e
– f
– =
– ‘
– h
– t
– t
– p
– s
– :
– /
– /
– w
– w
– w
– .
– s
– a
– l
– v
– a
– t
– i
– o
– n
– r
– e
– p
– a
– i
– r
– .
– c
– o
– m
– /
– r
– e
– p
– a
– i
– r
– ‘
– >
– s
– c
– h
– e
– d
– u
– l
– e
–
– a
–
– r
– e
– p
– a
– i
– r
– <
– /
– a
– >
– .
Step 17
– Gently detach the dock connector cable from the back panel assembly. You’ve got this!
