How to Replace Samsung Galaxy A15 Front Camera – DIY Guide

Duration: 45 minutes
Steps: 22 Steps

Get ready to swap out the front/selfie camera in your Samsung Galaxy A15! Just a heads up, when it’s time to put everything back together, make sure you’ve got some replacement adhesive handy for that back cover. Let’s do this!

Step 1

– First things first, unplug all those cables and make sure your phone is powered down completely. We want to give it a nice little nap!

– Now, press and hold the power button along with the volume down button at the same time. This will bring up the shutdown menu, just like magic!

Step 2

– Give your iOpener a little love and heat it up! Then, gently place it on the right edge of the back cover for a cozy two minutes. You’re doing great!

Tools Used
  1. iOpener
  2. Hair Dryer

Step 3

– While the adhesive is taking its sweet time to soften, here’s some handy info for you:

– There’s a layer of adhesive holding the back cover snugly around the edge of the frame.

Step 4

– Grab a suction handle and place it on the back cover, aiming for the center of the right edge like a pro.

– With a solid grip, pull up on that suction handle! Give it a good, steady tug to create a little gap between the cover and the frame.

– Now, slide in an opening pick into that gap you just made. You’re doing great!

Tools Used
  1. Suction Handle

Step 5

– Gently glide your opening pick along the right edge, slipping it between the back cover and the frame to cut through that pesky adhesive.

– Keep your opening pick wedged in the bottom right corner so the adhesive doesn’t decide to play peek-a-boo and reseal!

Step 6

– Give your iOpener a little time in the heat, then stick it to the bottom of the back cover for a cozy two minutes.

Tools Used
  1. iOpener

Step 7

– Pop in another opening pick at the bottom right corner and glide it along the bottom edge to cut through that sticky adhesive like a pro.

– Keep your opening pick snug in the bottom left edge to stop the adhesive from sealing back up. You’ve got this!

Step 8

– Warm up your iOpener and place it on the left side of the back cover for a cozy two minutes.

Tools Used
  1. iOpener

Step 9

– Slide another opening pick into the bottom left corner and gently glide it along the left edge to cut through that pesky adhesive.

– Keep your opening pick in the top left corner to stop the adhesive from sealing back up.

Step 10

– Warm up your iOpener and place it on the top of the back cover for a cozy two minutes.

Tools Used
  1. iOpener

Step 11

– Pop another opening pick into the top left corner, keeping it at the same depth, and glide it along the top edge to cut through that sticky adhesive like a pro.

– Keep your opening pick in the top right corner to stop the adhesive from sealing back up. You’re doing great!

Step 12

– Gently slide your trusty opening pick along the top edge of the phone and give it a little twist to release those camera clips like a pro!

– Now, take that same pick and glide it around the edges of the camera modules to pop off the rest of those clips. You’re doing great!

Step 13

– Once the adhesive around the edges has loosened up, gently slide your opening pick into the bottom edge, starting from the bottom left corner.

– Now, glide your pick further along the bottom edge, cutting through the remaining adhesive like a pro.

Step 14

– Go ahead and lift off that back cover like a pro!

– When it’s time to put everything back together:

– Use some tweezers or your fingers to gently pick away any leftover adhesive bits. If that sticky stuff is being stubborn, a little heat and some isopropyl alcohol (90% or higher) can work wonders.

– Got custom-cut adhesives? No worries, just follow this guide.

– Using double-sided tape? You got it—just check out this guide.

Step 15

– Grab your trusty SIM card eject tool, a bit, or even a straightened paperclip. Now, locate the tiny hole on the SIM tray, which is chilling at the top of your phone on the left edge.

– Give it a solid push to pop that tray out and remove it with ease!

Tools Used
  1. SIM Card Eject Tool

Step 16

– Time to get those screws out! Grab your trusty screwdriver and remove the fifteen screws that are holding the frame snugly to the chassis. They are 4 mm long, so keep an eye out for them!

Step 17

– Grab that trusty spudger and use the flat end to gently lift up and disconnect the fingerprint button press connector from the motherboard. You’ve got this!

Tools Used
  1. Spudger

Step 18

– Grab your trusty opening pick and gently slide it above the SIM card tray cutout to create a little space between the frame and the phone. You got this!

– Now, slide that opening pick down the left side of the device. This will help unclip those pesky frame clips. You’re on a roll!

Step 19

– Keep gliding your opening pick around the edge of the phone until every last clip has popped free. You’ve got this!

Step 20

– Gently remove the frame straight off the phone, like you’re peeling a banana—smooth and steady!

Step 21

– Grab your trusty spudger and gently lift up to disconnect that battery press connector. You’ve got this!

Tools Used
  1. Spudger

Step 22

– Grab your trusty spudger and gently lift up to disconnect that front camera press connector. Easy peasy!

– Now, simply pull out the front camera and give it a little wave goodbye!

Tools Used
  1. Spudger

Leave a Reply

Your email address will not be published. Required fields are marked *

🍪
Have a cookie! This site uses cookies to enhance your experience. Opt-Out Options.