How to Replace Samsung Galaxy S20 Ultra Earpiece Speaker Tutorial

– Grab your trusty SIM card eject tool, a handy bit, or even a straightened paperclip, and gently insert it into the tiny hole on the SIM tray. You’ll find this little gem at the top edge of your phone, right next to the plastic antenna band.

– Now, give it a firm push to pop that tray out like a pro!

– Start by popping out that SIM card tray. You’re doing great!

– When it’s time to put the SIM card back in, make sure it’s snug and snugly fits the tray’s groove. It’s all about that perfect alignment!

– Don’t forget about the thin rubber gasket that wraps around the SIM tray—it’s your phone’s little superhero against water and dust. If it’s looking worse for wear or has disappeared, consider swapping out the gasket or the whole tray. Protecting your phone’s insides is a smart move!

– Warm up an iOpener and place it on the bottom edge of the back cover for a cozy two minutes.

– Start by placing a suction cup right in the center of the bottom edge of your phone’s back—it’s like giving your device a little hug!

– Now, give that suction cup a good, strong pull—steady does it! This will help create a lovely gap between the back cover and the frame.

– Next up, take an opening pick and gently slide it into that new gap you’ve created. You’re doing great!

– Gently glide the pick back and forth along the bottom edge to cut through that sticky adhesive like a pro.

– Keep your opening pick snugly in the seam to stop the adhesive from sealing back up. You’ve got this!

– Warm up the left edge of the back cover with a heated iOpener for a cozy two minutes.

– Grab a suction cup and stick it to the back of your phone, aiming for the center of the left edge—it’s like giving your phone a little hug!

– Now, pull that suction cup with a strong, steady hand. You’re creating a gap between the back cover and the frame, so channel your inner superhero!

– Once you’ve got that gap, slide the point of an opening pick in there. You’re on your way to getting inside!

– Slide the pick under the edge of the glass and give it a little tilt downwards. Keep pushing it in to completely break that adhesive seal on the back cover. You’ve got this!

– Gently glide your pick down towards the bottom edge of the phone, gently coaxing the back cover away from its sticky embrace.

– Once you’ve got that pick in there, just leave it hanging out under the left side of the glass near the bottom. This will keep the adhesive from being too clingy again!

– Slide another pick right under the center of the left edge of the back cover. You’re doing great!

– Gently glide that pick towards the top of your device to break free the back cover’s adhesive. Patience is key!

– Keep your pick snug under the left edge of the glass near the top of the device to stop the adhesive from sticking back together. Nice job!

– Warm up the iOpener and give it a cozy two-minute hug on the right edge of the back cover.

– Start by placing a suction cup on the back of your phone, aiming for the center of the right edge. You’re doing great!

– Give that suction cup a firm, steady pull to create a little gap between the back cover and the frame. Keep up the good work!

– Now, take the point of an opening pick and gently slide it into that gap you’ve just created. You’re on the right track!

– Gently slide the pick down towards the bottom edge of the phone to break free the back cover’s sticky grip.

– Keep your pick tucked under the right edge of the glass near the bottom of the device to stop that adhesive from making a comeback.

– Slide another pick under the center of the right edge of the back cover—let’s get that party started!

– Gently glide the pick towards the top of the device to break free the back cover’s adhesive. It’s like peeling a sticker, but way more satisfying!

– Warm up an iOpener and place it on the top edge of the back cover for a cozy two minutes.

– Gently ease the pick into the right edge of your device, then glide it around the top right corner like you own the place.

– Keep slicing along the top edge to completely free the back cover from its adhesive hold. You’re doing great!

– Hey buddy, let’s gently pop that back cover off like a soda cap! If there’s any stubborn adhesive, our repair buddies at Salvation Repair might have some magic tricks up their sleeves. 😉 Check out this awesome reassembly tip:

– Time to reveal what’s hiding under the hood! So, if you need a little help, just let us know, and we can definitely arrange a repair date that’s totally chill.

– Coming up next, during the final stages of your tech-repair adventure! Schedule a repair any time, and don’t forget to have some fun along the way! 😎

– Grab your trusty spudger and gently pry up to disconnect that wireless charging coil connector. You’ve got this!

– Grab a trusty pair of tweezers and carefully peel the wireless charging coil away from the device. Easy does it!

– Now, gently remove the wireless charging coil. You’re doing great!

– When it’s time to put everything back together, start by reconnecting the wireless charging coil connector first. This helps you get everything aligned just right. Once that’s in place, give the rest of the coil a firm press to make sure it sticks nicely.

– Grab your trusty Phillips #00 screwdriver and get ready to tackle those five 3.9 mm-long screws holding the motherboard bracket in place. You’ve got this!

– Prepare to rock-and-roll! Use a pair of tweezers, like superheroes, to unclip and remove the motherboard bracket, taking your repair skills to the next level! If you need help, you can always schedule a repair.

– Grab your trusty spudger and gently wiggle it to lift up and disconnect that battery connector. You’ve got this!

– Grab your trusty Phillips #00 screwdriver and get ready to say goodbye to those five 3.9 mm-long screws holding onto the loudspeaker and lower midframe. Let’s make it happen!

– Gently slide the tip of a spudger or a trusty pair of tweezers into the notch at the top left corner of the midframe and give it a little pry to pop those clips loose. You’ve got this!

– Carefully lift out the loudspeaker and the lower midframe. You’re making great progress!

– Check out this neat trick! Puffins are super handy for freeing those snug little cable connectors. Give ’em a gentle nudge with your Puffin pal and watch ’em slip away real smooth. Oh, and when you’re ready to stick ’em back on, it’s like a game of Puffs and Luffs! Carefully line ’em up and give ’em a little press on both sides, making sure to avoid any pin-bending adventures. If your Puffin’s feeling a bit off-center, you can always schedule a repair to work out those kinks!

– Grab your trusty spudger and gently nudge those main and auxiliary flex cables away from the motherboard to disconnect them. You’re doing great!

– Start by gently lifting and removing the main and auxiliary flex cables.

– Gently lift and detach the snazzy 5G antenna cable on the left side from its perch on the motherboard.

– Gently lift and unplug the main display flex cable from the motherboard. If you need help, you can always schedule a repair.

– Lift and guide the display and the left 5G antenna flex cables gently aside from the motherboard and battery, just like a well-coordinated dance move.

– Grab your trusty Phillips #00 screwdriver and let’s tackle those four 3.9 mm-long screws holding the upper midframe in place. You’ve got this!

– Get ready to rock and roll by sliding the point of a spudger into the groove on the right side of the upper midframe. Gently pry upwards to unleash the magical clips that are keeping it snug as a bug.

– Give that upper midframe the VIP treatment and bid it farewell.

– Gently lift and unplug the right 5G antenna flex cable from the motherboard. You’ve got this!

– Grab a pair of tweezers and carefully nudge the cable aside to keep it out of the motherboard’s way. Easy peasy!

– Gently lift and unplug the side button flex cable from the motherboard. You’ve got this!

– Carefully bend the cable to keep it out of the motherboard’s way. Easy peasy!

– Gently pop up and disconnect the front-facing camera flex cable from the motherboard with ease.

– Carefully bend the cable aside to clear the path for the motherboard.

– Gently lift and unplug the upper 5G antenna cable from the motherboard. Remember, a little finesse goes a long way!

– Grab your trusty spudger and gently lift up the corner of the 5G millimeter wave antenna module. You got this!

– Now it’s time to bid farewell to the 5G antenna module. Out with the old!

– When putting everything back together, start by connecting the 5G antenna first. This will keep things nice and aligned. After that, give the rest of the antenna module a good press down to make sure it’s snug. Well done!

– Whoa-hey, put on your screws-funnels and ratchet those two tiny 3.9 mm screws loose like a pro! Watch as they un-lock and pop-off holding that fancy schmancy motherboard and camera combo! Excited? You should be! Ready to rock n’ roll? Let’s get it!

– Gently slide the spudger into the cozy bottom left corner of the motherboard assembly and give it a little nudge to free it from the phone body.

– Liberate the motherboard assembly with care and finesse.

– Oh boy, are we ready to get this funky speaker unstuck? Alrighty then, let’s carefully stick those pointy tweezers under the bottom left corner of the speaker, like superheroes! Next, we’ll lift that bad boy up and give it a friendly pat to unwind the sticky feet. Oh, and guess what? You can totally save that speaker glue if you’re using a shiny new speaker. But if you need to switch things up, check out our pre-cut adhesive sheets – it’s like putting on a fresh pair of socks!