Samsung Galaxy Note9 Fingerprint Sensor Replacement Guide – DIY Tutorial

Duration: 45 minutes
Steps: 14 Steps

Ready to get your groove back on that Samsung Galaxy Note9? Let’s swap out that fingerprint sensor together! It’s easier than you think, and you’ll be high-fiving yourself in no time. If you need help, you can always schedule a repair.

Step 1

– Before you start, make sure to power off your phone – it’s an important safety step.

– Now, let’s get that adhesive nice and soft. Use a hairdryer, a heatgun, or an iOpener and apply it to the right edge of the back of your phone for about a minute. If you need help, you can always schedule a repair

Tools Used
  1. iOpenerSamsung Galaxy Note9 Fingerprint Sensor Replacement

Step 2

– Grab a suction cup and stick it to the back cover like a pro.

– Give it a gentle pull to create a little space between the back cover and the phone’s frame.

– Slide an opening pick into that newly created gap and get ready to continue the adventure!

Tools Used
  1. Suction HandleSamsung Galaxy Note9 Fingerprint Sensor Replacement

Step 3

– Hey, you’ve got this! There’s a bit more sticky stuff along the top and around the camera, so be careful.

– Alright, now carefully cut along the left edge near the fingerprint sensor. It’s super important to be gentle here to avoid messing with the ribbon cable inside.

Step 4

– Let’s get started by cutting the adhesive on the right side, working from the center out. Use an opening pick to carefully cut up and down the right side.

Step 5

– Place an opening pick snugly in the upper-right corner to get things started.

– Grab another opening pick and carefully slice through the adhesive at the bottom-right corner.

– Keep that trusty opening pick in the phone for now; it’s doing a great job!

Step 6

– Ready to loosen up that adhesive? Let’s warm up the left side of the rear panel. Grab a heat gun or hairdryer (or maybe even a heated iOpener, those are cool, too) and give it a good three minutes of heat. This will make the adhesive underneath nice and malleable, making things a whole lot easier to work with.

Tools Used
  1. iOpenerSamsung Galaxy Note9 Fingerprint Sensor Replacement

Step 7

– Let’s get started by inserting an opening pick into the lower-left corner of the rear panel – easy does it!

– Now, grab another opening pick and carefully cut the adhesive along the left edge of the rear panel. If you need help, you can always schedule a repair

Step 8

– Now, with your trusty opening pick, let’s carefully cut through that sticky stuff around the top left corner of the back panel. You’ve got this!

– Time to finish up! Give that adhesive along the top of your phone a final snip. Almost there!

Tools Used
  1. iOpenerSamsung Galaxy Note9 Fingerprint Sensor Replacement

Step 9

– First things first, let’s tackle that right side of the rear cover! Give it a gentle separation.

– Now, give the cover a little tilt upwards along the left edge so you can sneak a peek at the fingerprint sensor ribbon cable.

Step 10

– Now it’s time to carefully pry the fingerprint sensor ribbon cable out of its socket – use the tip of a spudger to gently lift it up and out. If you need help, you can always schedule a repair

Tools Used
  1. SpudgerSamsung Galaxy Note9 Fingerprint Sensor Replacement

Step 11

– Time to get that back cover off! Start by removing it carefully.

– Now, let’s get that back cover back on:

– Grab some tweezers and gently peel away any leftover adhesive that’s still clinging to your phone’s chassis. After that, give those adhesion areas a good clean with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to get everything ready for the new adhesive. No need to get every speck of adhesive off—just make sure to remove the bigger chunks.

– Before sealing everything up, power on your phone and give your repair a test run. Better to check now than later!

– Finally, apply the new adhesive to the back cover with care. Line up one edge of the glass with the phone chassis and press it firmly into place. You’ve got this!

Step 12

– Grab your heat gun, hair dryer, or a heated iOpener and give that fingerprint sensor a warm hug from the outside. We’re aiming to soften that pesky adhesive hiding underneath. Keep heating it up until it’s just a tad too warm to touch; we want it cozy enough for the adhesive to loosen up without putting up a fight.

Tools Used
  1. iOpenerSamsung Galaxy Note9 Fingerprint Sensor Replacement

Step 13

– Slide an opening pick beneath the back of the fingerprint sensor.

– Gently twist the pick to pop the fingerprint sensor away from the back cover.

Step 14

– Time to ditch that old fingerprint sensor – carefully remove it from your device.

– Now, let’s get that new fingerprint sensor installed:

– Grab your trusty tweezers and gently peel off as much of the adhesive as you can. Next, use 90% isopropyl alcohol and a lint-free cloth to wipe away any remaining sticky stuff. If you need help, you can always schedule a repair

Leave a Reply

Your email address will not be published. Required fields are marked *

🍪
Have a cookie! This site uses cookies to enhance your experience. Opt-Out Options.