Samsung Galaxy S6 Edge Front Facing Camera Replacement
Duration: 45 minutes
Steps: 14 Steps
Ready to give your Samsung Galaxy S6 Edge a little camera makeover? This guide will help you swap out the front-facing camera with style! Just a heads up: we’ll be removing the rear glass to get to that sneaky camera, which means the adhesive might not survive the journey. No worries though! We’ll also walk you through reinstalling that rear glass like a pro. Let’s dive in!
Step 1
Hey there! Just a friendly reminder: keep that tool away from the microphone hole, or you might just give it a little too much love! And don't forget to check out the outline of the SIM tray. You've got this!
- Grab a paper clip or your trusty SIM eject tool and gently pop it into that little hole at the top of your phone's SIM card slot.
- Give it a nudge to pop out the SIM card tray.
- Carefully pull out the SIM card tray from your phone.
Step 2
Using a carousel microwave? Double-check that the plate spins smoothly—if your iOpener gets stuck, it could get too hot and burn. Keep things moving and stay safe!
Before diving into the fun stuff, give your microwave a quick clean-up. Any leftover gunk down there might just hitch a ride on the iOpener, and we don’t want that mess!
- Pop your iOpener right in the middle of the microwave.
Tools Used
Step 3
Keep an eye on that iOpener! Overheating can lead to a dramatic burst, and nobody wants that. So, let's keep it cool and below 100˚C (212˚F).
If the iOpener looks a bit puffy, steer clear! Safety first, folks.
If the center of your iOpener is still too hot to handle, hang tight! Keep using it while it cools down a bit before you give it another go. A nicely heated iOpener should stay cozy for about 10 minutes.
Microwaves can have different power levels, so you might need to adjust the time. The iOpener is ready to roll when it’s just on the edge of being too hot to handle.
- Give that iOpener a warm-up in the microwave for thirty seconds. It's like a cozy spa day for your tool!
- As you work through the repair, keep the vibe going by reheating the iOpener in the microwave for another thirty seconds whenever it starts to cool down. It's all about keeping that warmth flowing!
Tools Used
Step 4
Heads up! The iOpener is going to be pretty toasty, so handle it with care. An oven mitt might be your best buddy here!
- Carefully take the iOpener out of the microwave, grabbing it by one of the two flat ends to keep your fingers away from the heated center.
Tools Used
Step 5
The iOpener is going to be quite toasty, so make sure to grab it by the end tabs only. Stay safe and happy fixing!
No microwave? No problem! Just pop your iOpener in a pot of boiling water to get it warmed up.
- Grab a pot or pan and fill it up with enough water to give your iOpener a nice, warm bath.
- Get that water boiling and then turn off the heat — we want warmth, not a geyser!
- Gently toss the iOpener into the cozy water for 2-3 minutes, making sure it gets a full dunk.
- Use some tongs to carefully lift that warm iOpener out — it’s a little spa day for your tool!
- Give your iOpener a good towel-dry to ensure it's all set to go.
- And voilà! Your iOpener is primed and ready for action! If it needs a little warmth later on, just repeat the boiling water dance for another round.
Tools Used
Step 6
You can totally use a hair dryer, heat gun, or hot plate for this! Just remember to keep it cool—your phone's OLED display and internal battery are a bit sensitive to heat. Stay safe and happy repairing!
Remember, cracking open your phone will jeopardize its waterproof seals. Make sure you have some replacement adhesive at the ready before you dive in, or keep it away from water if you decide to seal it up without swapping out the adhesive.
If your screen is looking like a puzzle, slap some packing tape over the shattered glass to keep it together while you work your magic.
You might find yourself giving the iOpener a second (or third) chance at warming things up. Just keep an eye on it and follow the instructions to ensure you don’t raise the temperature too high.
- Place the heated iOpener on the back panel for about two minutes to help loosen the sticky adhesive holding the glass in place.
- Move the iOpener to a new spot and let it work its magic on the rest of the panel for another two minutes.
Tools Used
Step 7
Now that the pick is in place, consider adding a few drops of isopropyl alcohol to the gap. This will help loosen the adhesive, making the next steps a breeze. If you're unsure, don't worry - it's an optional step, but it can be a big help.
- When the back glass feels nice and toasty, stick a suction cup near the bottom edge.
- Give the suction cup a gentle pull to make a small gap, then slide an opening pick into the space you’ve created.
Step 8
Next up, it might be a good idea to keep that pick in place and grab a second one as you move on to the next step. Keeping the pick in can help stop that pesky glue from sticking back together.
Give the rear glass a little heat boost if needed to keep that glue from chilling out and hardening.
- Glide your pick along the bottom edge of the phone to loosen up the adhesive holding the rear glass in place.
Step 9
- Go ahead and warm up those edges and slice through the remaining three sides of the phone just like you did before!
- Pop an opening pick under each edge to keep that pesky adhesive from sticking back together.
Step 10
- Grab your trusty opening pick and gently glide it through any stubborn adhesive that's still hanging on.
- Carefully lift off the rear glass to unveil the inner workings of your device!
Step 11
- Ready to put on some fresh rear glass? Let’s go!
- If your new back glass doesn’t come with sticky stuff already attached—or you’re going old school and reusing the original—check out Salvation Repair’s guide to get it set up right.
- Grab your tweezers and pull off any leftover gunk or adhesive from the phone’s frame.
- Clean up the sticky zone with some high-strength isopropyl alcohol (90% or higher) and a lint-free cloth. Wipe in just one direction to make sure the surface is prepped for a solid stick.
- Peel off the new adhesive liner, carefully align the new glass (start with one edge snug against the chassis), and press down firmly to lock it in place.
Tools Used
Step 12
- Let's get started by unscrewing those thirteen 3.3 mm Phillips #00 screws from the midframe. You've got this!
Step 13
- Give a gentle push on the back of the battery while lifting the midframe edges up with a little flair to gracefully part them from the phone. You've got this!
Step 14
- Grab your trusty spudger and gently pry the front-facing camera away from the motherboard. You've got this!
- Now, carefully lift out the front-facing camera. Easy peasy!