Xbox One X Hard Drive Replacement Guide
Duration: 45 minutes
Steps: 23 Steps
Alright, let’s swap that Xbox One X hard drive! This guide’s here to help you replace the hard drive in your model 1787. Maybe your old drive’s giving you trouble, no worries, we’ve got this. First things first, power down your console and unplug those cables. We’re all about safety, so let’s follow those ESD guidelines while we’re at it. This guide’s all about that hard drive swap, but remember, you might need some extra tools to get that new drive working like a champ. If you’re feeling a bit lost, you can always schedule a repair.
Step 1
Hey there, techie! First things first, let’s power down that device. Go ahead and unplug any cables connected to it. We’re about to get this fixin’ party started!
– Grab a pair of blunt tweezers and gently peel away the sticker hiding the right-side screw on the back of the console. You’ve got this!
Step 2
– Grab your trusty T10 Torx screwdriver and let’s tackle those two screws! You’ll find them snugly sitting on the back of the console, each measuring a cool 12.6 mm in length. Unscrew them, and you’re one step closer to getting things back in action! If you need help, you can always schedule a repair.
Step 3
– Give that console a little spin! Rotate it 90 degrees, and watch it go.
– Now let’s give that upper plastic case a little love. Grab the front and pull it horizontally towards the front of the console. It’ll slide right out, like a piece of cake. Keep pulling until it stops, and those clips will pop out of their slots. You got this!
Step 4
– Give the console a little twist, rotating it 90 degrees so that the back is now facing you. You got this!
– Now, gently lift the left side of the upper plastic case (as you’re looking from the back of the console) and stop when it feels like it’s had enough lifting for now.
Step 5
If pushing up on the case isn’t doing the trick, give it a little wiggle in various directions until it finally swings open like it’s ready for a party!
– Now it’s time to get this case open – keep a firm grip on the left side of the upper plastic case and gently push up on the right side to move that screw boss out of the way.
– Next, swing the upper plastic case open to about 75 degrees, nice and smooth.
Step 6
– Gently nudge the upper plastic case down and away from the console to pop it off like a champ!
Step 7
– Time to unleash that inner tech wizard! Use the pointed end of a spudger, an opening tool, or even your trusty fingernail to gently flip down the small, hinged locking flap on the ribbon cable ZIF connector on the front circuit board. It’s like giving the connector a little high five!
Tools Used
Step 8
– Grab those trusty tweezers and give that ribbon cable a gentle nudge downwards, pulling it right out of the connector. You got this!
Step 9
– Grab your trusty T8 Torx screwdriver and get ready for some fun! Remove those three 13.3 mm screws that are keeping the front circuit board snugly attached to the upper metal case. You’re doing great!
Step 10
Hold onto the board firmly on either side of the connector—this will help you steer clear of any accidental bends or breaks. You’ve got this!
– Gently slide the front circuit board out from the upper metal case and place it to the side like a pro.
Step 11
– Grab your trusty T10 Torx screwdriver and go ahead and unscrew those six 47.7 mm screws that are keeping the upper metal case snugly in place against the lower plastic case.
– Now, switch to a T8 Torx screwdriver to tackle the two 7.5 mm screws holding the press connector to the upper metal case. You’re doing great!
Step 12
Be careful not to push the spudger too far into the socket – you don’t want to risk damaging it!
– Gently slide the flat end of a spudger beneath the press connector located on the side opposite the ribbon cable.
– Use that trusty spudger to carefully lift the press connector up and away from the upper metal case, giving it a little wiggle if needed.
– To snugly reattach press connectors like this one, align it just right and press down on one side until you hear that satisfying click. Then, do the same on the other side. Avoid pressing down in the center, though, as that might bend the pins and cause some serious trouble.
Tools Used
Step 13
Keep a firm grip on that lower plastic cover because it’s not clinging onto the metal case anymore!
– Turn the console upside down, it’s showtime!
– Gently pry the lower plastic casing away from the metal frame and place it to the side like a pro.
Step 14
– Time to get down to business! Start by loosening and removing those two T10 Torx screws that are holding the lower metal case hostage:
– One screw measuring 7.7 mm
– One screw measuring 11.4 mm
Step 15
Hey there! The disc drive might pop up a little as you remove the lower case. Just hold it down for a sec while you work. You got this!
– Gently lift the lower metal case away from the upper metal case and all those inner workings. You’re doing great!
– Now, go ahead and set the lower metal case aside for a moment. Keep up the good work!
Step 16
Hey, the disc drive is only held on by a couple of cable connectors. So, when you flip the console over, hold onto that disc drive so it doesn’t go flying off! You wouldn’t want to break anything, right?
– Let’s turn that console upside down and show it who’s boss! Now, grab your trusty T10 Torx screwdriver and let’s get those four 11.4 mm screws out. They’re keeping the hard drive snug in the upper metal case, and it’s time for a little freedom!
Step 17
The disc drive is snugly connected to the motherboard. Just a friendly reminder: be gentle with those cables! Pulling and bending them too much can cause some unwanted damage. Keep it cool and steady!
– Okay, it’s time to flip the console back over – just be careful since the disc drive is still loose.
– Lift the disc drive up gently, making sure its metal tab comes unhooked from the power supply. Easy does it!
– Now, flip the disc drive over and place it on the power supply. It should end up facing the opposite direction it was initially, nice and neat.
Step 18
– Gently lift the bundled cable connector that links the hard drive to the motherboard straight up. You’ve got this!
Step 19
– Gently tug on the SATA cable that’s linking your hard drive to the motherboard and lift it straight up. You’ve got this!
Step 20
When handling the hard drive, remember to grip it by the edges to keep it safe and sound!
– Gently lift the hard drive assembly out of its cozy spot in the upper metal case. You’ve got this!
Step 21
– Give that hard drive a little flip so the plastic mounting bracket is pointing skyward.
– Now, grab your trusty T10 Torx screwdriver and give those four 8.6 mm screws holding the hard drive to the bracket a little twist to loosen them up.
Step 22
– Gently lift the mounting bracket away from the hard drive, like it’s just waking up from a nap!
Step 23
– Time to bring your device back together! Just flip these steps around and you’re good to go.
– Got some electronics that need a new home? Swing by an R2 or e-Stewards certified recycler.
– Things didn’t turn out quite right? No worries! Give some basic troubleshooting a whirl, or hop over to our Xbox One X Answers community for a helping hand.
– Decided to take a different route? No problem at all!
– You’re not alone in this! A whole bunch of folks have tackled this guide successfully.
